Husqvarna 1330SB-XLSB owner manual BAG of Parts, Power Cord, Retainer PIN, Wrench

Page 38

REPAIR PARTS

BAG OF PARTS

SNOWTHROWER-MODELNO.1330SB-XLSB(96193004100),PRODUCTNO.9619300-41

		4
		14		6	7
	13	5		6	7
	13
	12
	12			9
			8	9
			8
3				10 11

01.14.003-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 19 85-63	POWER CORD
2	532 16 96-75	RETAINER PIN
3	532 18 06-84	WRENCH

4532 18 45-05 REMOTE SPRING

5532 17 98-29 SHOULDER BOLT 1/4−20

6532 17 92-46 NYLON WASHER 1/4−20

7532 19 17-30 LOCKNUT 1/4−20

8872 25 05-05 CARRIAGE BOLT 5/16−18 X 5/8

9532 75 11-53 LOCKNUT 5/16−18

10873 80 06-00 LOCKNUT 3/8−16

11	819 13 13-16	WASHER 3/8
12	532 19 86-36	SHEAR BOLT 1/4−20 X 1−3/4
13	532 19 86-38	SPACER
14	873 80 04-00	LOCKNUT 1/4−20

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
1	1	532 19 30-71 SAFETY IGNITION KEY
1

01.14.007-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 38

Image 38

Contents 1330SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents EXT RA Shear Bolts and Nuts Chute Deflector Remote ControlParts Packed Separately in Carton Rotator Head MountingRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigTo USE Drift Cutters See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationEngine CleaningSnow Thrower Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Assembly 30 LH Auger Assembly 30 RHAuger Ball Bearing Skid PlateWeight BAR CARRIAGEBOLT5/16−18X.750POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer StrapRotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot BracketHandles POP Rivet 1/8 01.12.002-C 532 42 14-48 Headlight Bezel Gray Grip Switch532 42 13-51 Console Panel Gray 532 17 86-66 Halogen HeadlightThrust Washer DriveAxle Shaft Clik PIN921 01.02.002-F Idler Pulley 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Clevis PIN01.01.001-B Frame Chassis / Engine / PulleysEngine Model Bottom PANSteer Cable Bracket LH Wheel Assembly LHWheels Steer Cable Bracket RHSpring CoverWheel Lobe Axle LobeBAG of Parts Power CordKEY Part Description 532 19 30-71 Safety Ignition KEY Retainer PIN532 18 37-30 DECAL, Remote Deflector Decals532 18 10-35 DECAL, DANGER, Deflector Warranty Statement

REPAIR PARTS

BAG OF PARTS

KEY

POWER CORD

RETAINER PIN

WRENCH

WASHER 3/8

KEY

PART

DESCRIPTION

532 19 30-71 SAFETY IGNITION KEY