Husqvarna 1330SB-XLSB owner manual Control Panel / Discharge Chute, Knob Black, POP Rivet

Page 25

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

SNOWTHROWER-MODELNO.1330SB-XLSB(96193004100),PRODUCTNO.9619300-41

5

7

16

3

17

6

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 42 17-14 CHUTE WELDMENT

2532 18 41-13 DEFLECTOR WELDMENT

3532 42 11-63 DEFLECTOR CONTROL ASSEMBLY

4532 42 03-25 DEFLECTOR SEAL

5	532 41 42-80	KNOB BLACK
6	532 12 84-15	POP RIVET

7817 50 10-10 SCREW 10−24 X .625

8532 41 98-21 CHUTE SNOW SHIELD

9532 42 17-28 SHIELD RETAINER STRAP

*10	532 17 98-29 SHOULDER BOLT 1/4−20 X .375
*11	532 17 92-46 PLASTIC WASHER
*12	532 19 17-30	NUT 1/4−20
*13	872 25 05-05	CARRIAGE BOLT 3/8−16 X .625	6
*14	532 75 11-53	NUT 5/16−18
*15	532 18 45-05	DEFLECTOR SPRING

16532 42 06-79 (SERVICE PART) DEFLECTOR CONTROL

17532 42 11-64 (SERVICE PART) DEFLECTOR CABLE GRAY

18532 42 11-38 DEFLECTOR SHIELD

19532 42 32-47 DEFLECTOR SHIELD STRAP

1819

6

19

	*15		*12
			*12
			*11
	2		*10
	4	6	*10
		6

6	*14

1

*13

01.09.006-C

9 8

NOTES:

1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 25

Image 25

Contents 1330SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlEXT RA Shear Bolts and Nuts Rotator Head MountingHOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigScraper BAR See Fig Before Starting the EngineTo USE Drift Cutters See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationSnow Thrower CleaningEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate Auger Ball BearingCARRIAGEBOLT5/16−18X.750 Weight BARKnob Black Control Panel / Discharge ChutePOP Rivet 532 42 17-28 Shield Retainer StrapCable Assembly Gray 532 42 11-60 LEVER/CABLE Rotator Assembly GrayRotator Head Rotator Pivot BracketHandles POP Rivet 1/8 01.12.002-C 532 42 13-51 Console Panel Gray Grip Switch532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightAxle Shaft DriveThrust Washer Clik PIN921 01.02.002-F 532 18 77-86 Traction Idler ARM 532 18 04-78 Engine Traction PulleyIdler Pulley Clevis PIN01.01.001-B Engine Model Chassis / Engine / PulleysFrame Bottom PANWheels Wheel Assembly LHSteer Cable Bracket LH Steer Cable Bracket RHWheel Lobe CoverSpring Axle LobeKEY Part Description 532 19 30-71 Safety Ignition KEY Power CordBAG of Parts Retainer PIN532 18 10-35 DECAL, DANGER, Deflector Decals532 18 37-30 DECAL, Remote Deflector Warranty Statement