Husqvarna 1130SB-LS owner manual HOW to USE Your Snow Thrower, Stopping

Page 10

OPERATION

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear

safety glasses or eye shields while operating your snow thrower or performing any adjust- ments or repairs. We recommend standard safety glasses

or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or attempting to start the engine.

STOPPING

TRACTION DRIVE

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

AUGER

•Release the auger control lever to stop throwing snow.

ENGINE

1.Move throttle control to “STOP” position.

2.Remove (do not turn) safety ignition key to prevent unauthorized use.

NOTE: Never use choke to stop engine.

TO USE FUEL SHUT-OFF VALVE (See Fig. 11)

The fuel shut-off valve is located beneath the fuel tank on the engine. Always operate the snow thrower with the fuel shut-off valve in the OPEN position.

OFF

OPEN

FIG. 11

TO USE THROTTLE CONTROL (See Fig. 12)

The throttle control is located on the engine. Always operate the snow thrower with the engine at full throttle. Full throttle offers the best snow thrower performance.

FAST

SLOW

FIG. 12

10

TO USE CHOKE CONTROL (See Fig. 13)

The choke control is located on the engine. Use the choke control whenever you are starting a cold engine. Do not use to start a warm engine.

•To engage choke, turn knob clockwise. Slowly turn knob counterclockwise to disengage.

OFFFULL

FIG. 13

TO CONTROL SNOW DISCHARGE (See Fig. 14)

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

WARNING: If the discharge chute or auger become clogged, shut-off engine and wait for all moving parts to stop. Use the clean-out tool, NOT YOUR HANDS, to unclog the chute and/or auger.

The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever.

•To change the discharge chute position, press downward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position.

The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to throw snow a short distance; set the deflector higher to throw snow farther.

•Press downward on chute deflector control lever and move lever forward to raise the deflector and increase the distance. Move lever back to lower the deflector and decrease the distance. Be sure lever springs back and locks into desired position.

DISCHARGE CHUTE

CONTROL LEVER

CHUTE DEFLECTOR

REMOTE CONTROL LEVER

FIG. 14

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 1130SB-LS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping To Start EngineIf Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Ball Bearing Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate 01.16.001-A POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer StrapRotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot BracketHandles POP Rivet 1/8 01.05.006-A Repair Parts 532 17 86-66 Halogen Headlight Grip Switch532 42 14-48 Headlight Bezel Gray BulbDrive 532 19 77-63 Drive Plate Weldment 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly HEX Shaft532 18 00-82 Intermediate Gear 532 40 61-09 Control Shaft AssemblyAssembly 532 19 95-09 Rubber Wheel PlateGear Axle ShaftRoll PIN 3/16 Clik PINClutch Slide CoverWheel Lobe Axle LobeFrame Bottom PANPulley Chassis / Engine / PulleysImpeller Belt Wheels BAG of Parts Power Cord532 03 50-62 Safety Ignition KEY Retainer PINDECAL, Husq DECAL, Husq 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Service Notes Service Notes Warranty Statement
Top Page Image Contents