Husqvarna 1130SB-LS owner manual Repair Parts

Page 30

REPAIR PARTS							HANDLES
SNOW THROWER - MODEL NO. 1130SB-LS (96193002900), PRODUCT NO. 961 93 00-29
	2
					KEY	PART	DESCRIPTION
					NO.	NO.	DESCRIPTION
					1	532 18 04-80 IMPELLER ROD ASSEMBLY
					2	532 40 57-40 TRACTION ROD ASSEMBLY
1					3	532 18 04-45 SHIFTER ROD TOP
1					4	532 18 77-16 SHIFTER ROD BOTTOM
					4	532 18 77-16 SHIFTER ROD BOTTOM
					5	532 18 04-47 SPRING SLEEVE
					6	532 17 86-69 IMPELLER SPRING
					7	532 18 09-26 TRACTION SPRING
					8	872 27 05-06	CARRIAGE BOLT 5/16−18 X .750
					9	532 15 53-77	NUT 5/16−18
					10	532 16 96-75	RETAINER
	3				11	532 40 33-00	CLUTCH ROD
9					12	532 41 69-21	REAR PLATE
9					13	532 41 54-33 SHIFTER PLATE BRACKET
	8				14	532 41 68-64 CLUTCH PLATE BRACKET
		5			15	532 41 54-35 CLUTCH PLATE
					16	532 41 54-50 SHIFTER PLATE
	4				17	817 49 05-08 BOLT 5/16−18 X .500
			7		18	532 40 28-81	SHOULDER BOLT 1/4−20 X .500
			18		19	532 19 17-30	NUT 1/4−20
			18
5	18		17	19
5	18		19	19
		18	19
		18	15
			15
			14
	10
6	16					11
	17	13				11
		19
			12		01.12.006-A

2

1 01.15.008-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 42 12-31	STEER CABLE
2	874 04 10-24	SCREW 10−24 X 1.50

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 30

Image 30

Contents 1130SB-LS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine To Start Engine Before StoppingIf Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Ball Bearing Auger Assembly 30 LH Auger Assembly 30 RHSkid Plate 01.16.001-A POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer StrapRotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot BracketHandles POP Rivet 1/8 01.05.006-A Repair Parts 532 17 86-66 Halogen Headlight Grip Switch532 42 14-48 Headlight Bezel Gray BulbDrive 532 19 77-63 Drive Plate Weldment 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly HEX Shaft532 18 00-82 Intermediate Gear 532 40 61-09 Control Shaft AssemblyAssembly 532 19 95-09 Rubber Wheel PlateGear Axle ShaftRoll PIN 3/16 Clik PINClutch Slide CoverWheel Lobe Axle LobeFrame Bottom PANChassis / Engine / Pulleys PulleyImpeller Belt Wheels BAG of Parts Power Cord532 03 50-62 Safety Ignition KEY Retainer PINDECAL, Husq 532 18 10-35 DECAL, DANGER, Deflector DECAL, Husq532 18 37-30 DECAL, Remote Deflector Service Notes Service Notes Warranty Statement