Husqvarna 1130SB-LS owner manual Auger Assembly 30 LH, Auger Assembly 30 RH, Skid Plate

Page 23

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 1130SB-LS (96193002900), PRODUCT NO. 961 93 00-29

2

1

KEY

PART

DESCRIPTION

NO.

NO.

1

532 42 17-26

AUGER ASSEMBLY 30 LH

2

532 42 17-27

AUGER ASSEMBLY 30 RH

01.07.016-A

2

 

3

 

 

 

 

1

 

3

 

 

 

 

KEY

PART

DESCRIPTION

 

NO.

NO.

 

1

532 40 78-34

SKID PLATE

 

2

872 27 05-06

CARRIAGE BOLT 5/16−18 X .750

01.11.002-A

3

532 75 11-53

NUT 5/16−18

2

1

 

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents 1130SB-LS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigBefore Starting the Engine If Recoil Starter has Frozen To Start EngineBefore Stopping Lubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Ball Bearing Skid Plate Auger Assembly 30 LHAuger Assembly 30 RH 01.16.001-A 532 42 17-28 Shield Retainer Strap Control Panel / Discharge ChuteKnob Black POP RivetRotator Pivot Bracket 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator HeadHandles POP Rivet 1/8 01.05.006-A Repair Parts Bulb Grip Switch532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightDrive HEX Shaft 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 532 19 77-63 Drive Plate Weldment532 19 95-09 Rubber Wheel Plate 532 40 61-09 Control Shaft AssemblyAssembly 532 18 00-82 Intermediate GearClik PIN Axle ShaftRoll PIN 3/16 GearAxle Lobe CoverWheel Lobe Clutch SlideBottom PAN FrameImpeller Belt Chassis / Engine / PulleysPulley Wheels Retainer PIN Power Cord532 03 50-62 Safety Ignition KEY BAG of Parts532 18 37-30 DECAL, Remote Deflector DECAL, Husq 532 18 10-35 DECAL, DANGER, DeflectorDECAL, Husq Service Notes Service Notes Warranty Statement
Top Page Image Contents