Husqvarna 1130SB-LS owner manual KEY Part Description

Page 21

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 1130SB-LS (96193002900), PRODUCT NO. 961 93 00-29

KEY	PART		DESCRIPTION
NO.	NO.		DESCRIPTION
1	532	18 41-05	IMPELLER
2	532	19 67-10	GEARBOX ASSEMBLY
3	532	18 89-09	BEARING

4532 19 10-79 IMPELLER PULLEY

5532 17 53-22 DISCHARGE BASE

6532 18 40-95 CORNER BRACKET

7532 19 21-99 CLEAN OUT TOOL

8	532 40 54-00	TOOL CLIP
9	873 80 04-00	NUT 1/4−20
10	874 78 04-26 SCREW 1/4−20 X .625
11	532 15 53-77	NUT 5/16−18
12	532 16 31-83 SCREW 5/16−18 X .625
13	819 11 15-07	WASHER

14810 04 05-00 LOCKWASHER 5/16

15874 94 05-16 SCREW 5/16−18 X 1.00

16532 18 03-55 CARRIAGE BOLT

17532 19 41-89 SCREW 13−16 X .625

18	532 40 77-60	PLUG
19	532 40 77-61 GEARBOX COVER RH
20	532 40 77-66	GASKET
21	532 40 77-70	SEAL
22	532 40 77-62	BEARING
23	532 17 46-97 THRUST WASHER 1.00
24	532 40 77-63	WORM GEAR
25	532 40 77-64	AUGER SHAFT
26	532 18 92-82	SQUARE KEY
27	532 40 77-58	BEARING

28532 17 46-83 THRUST WASHER

29532 40 77-57 IMPELLER SHAFT

30	532 18 42-05 ROLL PIN

31532 17 46-81 THRUST WASHER

32532 17 46-84 THRUST BEARING

33	532 40 77-69	BEARING
34	532 40 77-68	O−RING

35532 40 77-67 SCREW 5/16−18 X .750

36532 40 77-65 GEARBOX COVER LH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 21

Image 21

Contents 1130SB-LS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine To Start Engine Before StoppingIf Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Ball Bearing Auger Assembly 30 LH Auger Assembly 30 RHSkid Plate 01.16.001-A Knob Black Control Panel / Discharge ChutePOP Rivet 532 42 17-28 Shield Retainer StrapCable Assembly Gray 532 42 11-60 LEVER/CABLE Rotator Assembly GrayRotator Head Rotator Pivot BracketHandles POP Rivet 1/8 01.05.006-A Repair Parts 532 42 14-48 Headlight Bezel Gray Grip Switch532 17 86-66 Halogen Headlight BulbDrive Trunnion Bearing Assembly 532 19 84-74 Speed Selector Head Assembly532 19 77-63 Drive Plate Weldment HEX ShaftAssembly 532 40 61-09 Control Shaft Assembly532 18 00-82 Intermediate Gear 532 19 95-09 Rubber Wheel PlateRoll PIN 3/16 Axle ShaftGear Clik PINWheel Lobe CoverClutch Slide Axle LobeBottom PAN FrameChassis / Engine / Pulleys PulleyImpeller Belt Wheels 532 03 50-62 Safety Ignition KEY Power CordBAG of Parts Retainer PINDECAL, Husq 532 18 10-35 DECAL, DANGER, Deflector DECAL, Husq532 18 37-30 DECAL, Remote Deflector Service Notes Service Notes Warranty Statement