Husqvarna 1130SB-LS owner manual Washer, POP Rivet 1/8

Page 28

REPAIR PARTS

HANDLES

SNOW THROWER - MODEL NO. 1130SB-LS (96193002900), PRODUCT NO. 961 93 00-29

					1
			5	6
	10			6
	10
			8		7
			2
	5	8		3	9
	5			3

		6		7
		8
		4	9
		4
KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 42 17-08 PLOW HANDLE LH

2532 42 17-09 PLOW HANDLE RH

3	532 19 69-44 PANEL BRACKET LH

4532 19 69-43 PANEL BRACKET RH

5532 41 45-15 HEATED HANDLE GRIP

6	874 78 05-12 SCREW 5/16−18 X .750		01.08.011-A
7	874 78 05-24	SCREW 5/16−18 X 1.50	01.08.011-A
7	874 78 05-24	SCREW 5/16−18 X 1.50
8	532 75 11-53	NUT 5/16−18
9	532 15 54-15	WASHER
10	532 17 87-75	POP RIVET 1/8

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 28

Contents 1130SB-LS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping To Start EngineIf Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Ball Bearing Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate 01.16.001-A Control Panel / Discharge Chute Knob BlackPOP Rivet 532 42 17-28 Shield Retainer Strap532 42 11-60 LEVER/CABLE Rotator Assembly Gray Cable Assembly GrayRotator Head Rotator Pivot BracketHandles POP Rivet 1/8 01.05.006-A Repair Parts Grip Switch 532 42 14-48 Headlight Bezel Gray532 17 86-66 Halogen Headlight BulbDrive 532 19 84-74 Speed Selector Head Assembly Trunnion Bearing Assembly532 19 77-63 Drive Plate Weldment HEX Shaft532 40 61-09 Control Shaft Assembly Assembly532 18 00-82 Intermediate Gear 532 19 95-09 Rubber Wheel PlateAxle Shaft Roll PIN 3/16Gear Clik PINCover Wheel LobeClutch Slide Axle LobeFrame Bottom PANPulley Chassis / Engine / PulleysImpeller Belt Wheels Power Cord 532 03 50-62 Safety Ignition KEYBAG of Parts Retainer PINDECAL, Husq DECAL, Husq 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Service Notes Service Notes Warranty Statement

REPAIR PARTS

HANDLES

SNOW THROWER - MODEL NO. 1130SB-LS (96193002900), PRODUCT NO. 961 93 00-29

KEY

WASHER

POP RIVET 1/8