Husqvarna 1130SB-LS owner manual Control Panel / Discharge Chute, Knob Black, POP Rivet

Page 25

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

SNOW THROWER - MODEL NO. 1130SB-LS (96193002900), PRODUCT NO. 961 93 00-29

5

7
16
3	18	19
17	18
17
		6
	19
	6

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 42 17-14 CHUTE WELDMENT

2532 18 41-13 DEFLECTOR WELDMENT

3532 42 11-63 DEFLECTOR CONTROL ASSEMBLY

4532 42 03-25 DEFLECTOR SEAL

5	532 41 42-80	KNOB BLACK
6	532 12 84-15	POP RIVET

7817 50 10-10 SCREW 10−24 X .625

8532 41 98-21 CHUTE SNOW SHIELD

9532 42 17-28 SHIELD RETAINER STRAP

*10	532 17 98-29 SHOULDER BOLT 1/4−20 X .375
*11	532 17 92-46 PLASTIC WASHER
*12	532 19 17-30	NUT 1/4−20	6
*13	872 25 05-05	CARRIAGE BOLT 3/8−16 X .625
*14	532 75 11-53	NUT 5/16−18
*15	532 18 45-05	DEFLECTOR SPRING

16532 42 06-79 (SERVICE PART) DEFLECTOR CONTROL

17532 42 11-64 (SERVICE PART) DEFLECTOR CABLE GRAY

18532 42 11-38 DEFLECTOR SHIELD

19532 42 11-39 DEFLECTOR SHIELD STRAP

	*15		*12
			*12
			*11
	2		*10
	4	6	*10
		6

6	*14

1

*13

01.09.006-C

9 8

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 25

Image 25

Contents 1130SB-LS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping To Start EngineIf Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Ball Bearing Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate 01.16.001-A Knob Black Control Panel / Discharge ChutePOP Rivet 532 42 17-28 Shield Retainer StrapCable Assembly Gray 532 42 11-60 LEVER/CABLE Rotator Assembly GrayRotator Head Rotator Pivot BracketHandles POP Rivet 1/8 01.05.006-A Repair Parts 532 42 14-48 Headlight Bezel Gray Grip Switch532 17 86-66 Halogen Headlight BulbDrive Trunnion Bearing Assembly 532 19 84-74 Speed Selector Head Assembly532 19 77-63 Drive Plate Weldment HEX ShaftAssembly 532 40 61-09 Control Shaft Assembly532 18 00-82 Intermediate Gear 532 19 95-09 Rubber Wheel PlateRoll PIN 3/16 Axle ShaftGear Clik PINWheel Lobe CoverClutch Slide Axle LobeBottom PAN FramePulley Chassis / Engine / PulleysImpeller Belt Wheels 532 03 50-62 Safety Ignition KEY Power CordBAG of Parts Retainer PINDECAL, Husq DECAL, Husq 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Service Notes Service Notes Warranty Statement