Ariens 932102 - 520, 932103 - 624, 932310 - 624 manual Attachment Clutch / Brake Adjustment

Page 19

Cap Screws

Figure 8

OS1881

ATTACHMENT CLUTCH / BRAKE ADJUSTMENT

WARNING: IMPROPER ADJUSTMENT could result in unexpected movement of auger and impeller causing death or serious injury. Auger/impeller must stop within 3 seconds when attachment clutch bail is released.

1.Remove belt cover.

2.Check belt alignment (Figure 9).

Engine sheave and attachment pulley must align vertically. Also, belt must be centered in the idler pulley.

To move pulley or sheave:

a.Loosen set screw.

b.Slide pulley/sheave and key to desired position.

c.Tighten set screw.

3.Adjust cable slack.

IMPORTANT: The clutch cable must be slack when the bail is disengaged.

a.With clutch bail disengaged, loosen jam nut on cable adjuster.

b. Lift spring arm, but do not move idler arm.

c.Turn adjuster body to remove all slack from the cable. Do not stretch spring or move idler arm.

d.Release spring arm and turn back the adjuster body 5 turns (approximately 1/4 in or 6 mm). Finger tighten jam nut.

e. Hold adjuster body with pliers and tighten jam nut with wrench.

4.Check spring length.

a.Measure the length of the clutch cable spring.

b.Engage and hold the attachment clutch bail.

c.Measure the length of the spring again. The spring should be 1/8-3/16 in (3-5 mm) longer when the bail is engaged.

5.Adjust spring length.

a.Loosen the idler adjustment nut.

b.To increase spring extension, move idler towards belt (Figure 7).

c.To decrease spring extension, move idler away from belt.

d.Tighten idler adjustment nut.

6.Check brake.

When the clutch bail is disengaged, the brake must contact attachment belt.

When the clutch bail is engaged, the brake must be more than 1/16 in (1.6 mm) away from the belt.

7.Repeat steps 4 – 6 until:

Spring stretch and brake contact are correct.

IMPORTANT: If attachment clutch/brake cannot be adjusted within tolerances, see your Dealer for repairs.

8.Check belt finger clearance.

With clutch bail engaged, belt fingers should be 1/16 – 1/8 in (1.6–3 mm) from belt. Adjust belt fingers as necessary.

9.Replace belt cover.

10.Check that auger/impeller stops within 3 seconds after attachment clutch/ impeller brake bail is released.

GB - 19

Image 19
Contents Sno-Thro Category Walk Behind Snow Thrower Livello di potenza sonora garantito English Français Español Controls and Features932102 Introduction Table of ContentsSafety Safety Sécurité Safety Decals LocationsOperational Safety Rules Assembly Safety RulesTransport Fuel Safety RulesCleaning Hazardous SlopesAccessory and Attachment Safety Rules AssemblyMaintenance and Service Safety Rules Storage Safety RulesCheck Attachment Clutch Cable Discharge ChuteOperation Controls and FeaturesFilling Fuel Tank PRE-STARTStarting and SHUT-OFF Traveling Snow RemovalTransport Maintenance Schedule MaintenanceAuger Shaft General LubricationRemove old attachment drive belt Service and AdjustmentsAttachment Drive Belt Replacement Install new attachment drive beltAttachment Clutch / Brake Adjustment Discharge Chute Shear Bolts For ReplacementStorage TroubleshootingService Parts AccessoriesEngine Tecumseh SpecificationsYear Limited Sno-Thro Warranty DURA-CLEAN Auger Limited Lifetime Warranty
Related manuals
Manual 25 pages 28.84 Kb

932103 - 624, 932102 - 520, 932310 - 624 specifications

Ariens is a well-known brand in the outdoor power equipment industry, particularly recognized for its high-performance snow blowers. Among its notable models, the Ariens 932310 - 624, 932102 - 520, and 932103 - 624 stand out for their robust construction and innovative features designed to tackle harsh winter conditions.

The Ariens 932310 - 624 is engineered for heavy-duty snow removal with a 24-inch clearing width and a powerful 624cc engine. This model features a reliable Ariens Polar Engine that provides efficient power and ensures consistent performance even during the coldest months. The durable housing construction, combined with a heavy-duty steel frame, offers superior durability and stability, making it an ideal choice for homeowners and professionals alike.

The 932102 - 520 model, with its 20-inch clearing width, is designed for those who require a more compact yet powerful option. Equipped with a 520cc engine, it provides ample power for residential snow removal tasks. This model includes Ariens' patented Auto-Turn technology, allowing for easy maneuverability around trees, mailboxes, and sidewalks. The lightweight, compact design enables storage in smaller spaces, making it suitable for urban environments.

On the other hand, the Ariens 932103 - 624 combines the best features of performance and versatility. With a larger 24-inch clearing width and a powerful 624cc engine, this model excels in clearing heavy snowfall. It also includes features like adjustable chute control, allowing users to direct snow where they want it to go with minimal effort. The heavy-duty tires provide excellent traction, necessary for navigating slippery driveways and pathways.

All three models come equipped with essential safety features, including an ignition switch and safety key to prevent accidental starts. Their ergonomic handlebars and controls are designed for comfort, ensuring ease of use regardless of the operator's experience level. Additionally, each model boasts a two-stage snow removal system that efficiently manages heavy snow, ensuring effective clearing with every pass.

In summary, the Ariens 932310 - 624, 932102 - 520, and 932103 - 624 models bring together powerful engines, durable construction, and advanced technology to provide effective snow removal solutions. They cater to different needs and preferences, making them versatile choices for anyone looking to combat snow build-up efficiently during winter.