Snow Removal, Traveling, Transport | Ariens 932103

5.Insert key into ignition switch and push into RUN position. DO NOT twist key after inserting it.

6.Grasp starter handle and pull rope out slowly until it pulls harder. Let rope rewind slowly.

7.Pull rope with a rapid continuous full arm stroke. Let rope rewind slowly.

NOTE: DO NOT allow starter handle to snap back against the starter.

8.Repeat steps 6 and 7 until the engine starts. (If engine does not start, refer to Troubleshooting.)

9.Adjust choke as needed.

10.Set throttle to Part Throttle or Slow position for adaptation to outside temperature. Set throttle to Fast Throttle position for normal operation.

Electric Start (120V or 240V)

(932103, optional on 932102, 310)

1.Connect extension cord to prongs on starter.

IMPORTANT: Prevent damage to unit. Know voltage of your starter and only use matching outlets.

2.Plug extension cord into:

240V 3-wire, grounded outlet.

120V 3-wire, grounded outlet.

3.Turn discharge chute straight ahead.

4.Make sure that the attachment clutch bail is fully disengaged.

5.Push Primer Bulb 2 or 3 times for cold engine.

NOTE: When temperature is below

-15˚F (-26˚C) additional priming may be needed.

6.Insert key into ignition switch on engine and push into "Run" position. DO NOT twist key after it is inserted.

7.If engine is cold, apply choke. A warm engine requires less choking than a cold engine. See Engine Manual for detailed instructions.

8.Set throttle to proper starting position.

9.Press starter button on engine until engine starts.

IMPORTANT: DO NOT operate starter more than 15 seconds per minute, as overheating and damage can occur. (If engine does not start, refer to Troubleshooting.)

10.Adjust choke as needed.

11.Disconnect power cord from outlet, then starter.

12.Set throttle to Part Throttle or Slow position for adaptation to outside temperature. Set throttle to Fast Throttle position for normal operation.

Emergency Stop

Immediately release clutch bail to stop unit in an emergency. Stop Engine, remove Key and wait for all rotating parts to stop before leaving operator’s position.

Shut-Off

1.Run Impeller a few minutes after use to prevent freeze-up of Impeller.

2.Release Attachment Clutch Bail.

3.Move Throttle to the "Stop" Position.

4.Remove key.

SNOW REMOVAL

IMPORTANT: Allow unit and engine to adjust to the outdoor temperatures before clearing snow.

1.Select discharge chute and deﬂector position and direction.

2.Engage Attachment Clutch bail.

NOTE: The auger propels unit forward. Keep a ﬁrm grip on handlebar when engaging bail.

IMPORTANT: DO NOT overload unit capacity by attempting to clear snow at too fast a rate.

Tips for Operation

Snow is best removed as soon as possible after snow fall.

To clear an area, run unit in an overlapping series of paths. For large areas; start in the middle and throw snow to each side, so snow is not cleared more than once.

ALWAYS direct snow away from area to be cleared and with direction of the wind.

TRAVELING

To travel from one work area to another:

1.Release Attachment Clutch Bail.

2.Set Throttle to Slow position or Part Throttle position.

3.Press down the handlebars enough to raise the front of the unit slightly off surface.

4.Push unit to desired location.

TRANSPORT

ALWAYS shut off engine, remove key and drain fuel when transporting unit on a truck or trailer.

Use extra care when loading or unloading unit onto trailer or truck.

GB - 15

932103 - 624, 932102 - 520, 932310 - 624 specifications

Ariens is a well-known brand in the outdoor power equipment industry, particularly recognized for its high-performance snow blowers. Among its notable models, the Ariens 932310 - 624, 932102 - 520, and 932103 - 624 stand out for their robust construction and innovative features designed to tackle harsh winter conditions.

The Ariens 932310 - 624 is engineered for heavy-duty snow removal with a 24-inch clearing width and a powerful 624cc engine. This model features a reliable Ariens Polar Engine that provides efficient power and ensures consistent performance even during the coldest months. The durable housing construction, combined with a heavy-duty steel frame, offers superior durability and stability, making it an ideal choice for homeowners and professionals alike.

The 932102 - 520 model, with its 20-inch clearing width, is designed for those who require a more compact yet powerful option. Equipped with a 520cc engine, it provides ample power for residential snow removal tasks. This model includes Ariens' patented Auto-Turn technology, allowing for easy maneuverability around trees, mailboxes, and sidewalks. The lightweight, compact design enables storage in smaller spaces, making it suitable for urban environments.

On the other hand, the Ariens 932103 - 624 combines the best features of performance and versatility. With a larger 24-inch clearing width and a powerful 624cc engine, this model excels in clearing heavy snowfall. It also includes features like adjustable chute control, allowing users to direct snow where they want it to go with minimal effort. The heavy-duty tires provide excellent traction, necessary for navigating slippery driveways and pathways.

All three models come equipped with essential safety features, including an ignition switch and safety key to prevent accidental starts. Their ergonomic handlebars and controls are designed for comfort, ensuring ease of use regardless of the operator's experience level. Additionally, each model boasts a two-stage snow removal system that efficiently manages heavy snow, ensuring effective clearing with every pass.

In summary, the Ariens 932310 - 624, 932102 - 520, and 932103 - 624 models bring together powerful engines, durable construction, and advanced technology to provide effective snow removal solutions. They cater to different needs and preferences, making them versatile choices for anyone looking to combat snow build-up efficiently during winter.