Filling the Tank, Test with Clean Water | Unigreen P300, P600, P500

FIG. 10

FIG. 11

FIG. 12

WARNING: using the taps on the pump or in any case on the front of the machine puts the operator near the cardan shaft. Despite the presence of CE standard protective covers you should take great care.

4.10 FILLING THE TANK

The machines for defensive crop treatments, in consideration of the safety of persons, animals and the protection of the environment, must only be filled indirectly from open water courses and only by free-falling water from the waterworks.

The pipe used for filling must never come into contact with the liquid inside the tank and therefore the water must always fall over the upper edge of the filling inlet and through the filter installed on it.

The tank is fitted with a transparent graduated band that shows the exact quantity of liquid inside. This reading is precise if the tank is on flat ground; the actual total capacity coincides with the highest number. All the filling systems fitted by Unigreen on their production machines or on request are antipollution and stop the liquid overflowing out of the tank.

a)FILLING WITH THE 3-WAY DEVIATOR (Fig. 10- Fig. 11).

It is possible to fill the tank using the pump and the floating filter kit G (cod.1002/ 0080F) with 6 metres of rubber hose (the floating filter lets you always and only suck up clean water).

=connect hose T to deviator D using the union hose adaptor supplied.

=turn the lever of deviator D to the filling position.

=place the other end of the hose, on which you fitted filter G, in the watering point.

=start the power-takeoff leaving pressure regulator C in the draining position (you don’t have to put the pump under pressure).

=the filling speed in litres/minute is equal to the delivery of pump P.

=visually check the level of the liquid in the tank and after filling stop the pump and put the lever of deviator D back in the working position.

=disconnect pipe T from deviator D.

b)FILLING WITH THE SUCTION FILTER (Fig. 3- Fig. 11).

If the 3-way deviator isn’t fitted you can fill the tank using the coupling on the cover of the suction filter. Unscrew the rear wing nut of the filter and using a G1"1/2 threaded union, connect pipe T with the floating filter to the coupling. Also in this case the filling speed in litres/minute is equal to the delivery of the pump.

c)FILLING WITH THE ANTIPOLLUTION EJECTOR (Fig. 12)

If you are filling with an antipollution hydroejector (mounted as standard on some models) then you should proceed as follows:

=put roughly 20-30 L of water in the tank and start the pump.

=remove the cap of ejector E and insert filling pipe T.

=place the other end of the hose, on which you fitted filter G, in the watering point.

=open the tap that supplies the ejector (on auxiliary taps, see point 4.9).

=increase the pressure until it reaches a value which is sufficient to suck up the liquid.

=visually check the level of the liquid inside the tank and after filling disconnect pipe T from the ejector, close the tap and replace the cap.

4.11 TEST WITH CLEAN WATER

It is good practice to do a test with clean water (without chemical product in the tank) before the first treatment to make sure the mistblower is working properly and to get to know the controls. For instructions on how to proceed with the treatment see the chapter SPRAYING.

14unigreen

P400, P300, P500, P600 specifications

Unigreen is a leading manufacturer in the agricultural machinery sector, known for its innovative solutions that meet the growing demands of modern farming. Among its impressive lineup, the Unigreen P400, P300, P600, and P500 series have garnered attention for their advanced features, cutting-edge technologies, and exceptional performance.

The Unigreen P400 is a versatile sprayer suitable for medium to large-sized farms. One of its key features is the high-capacity tank that minimizes the need for frequent refills, allowing farmers to cover substantial areas in a single pass. The sprayer is equipped with advanced precision technology that ensures uniform application of chemicals, which is crucial for maximizing crop yield while minimizing waste.

On the other hand, the Unigreen P300 is designed for smaller operations but does not compromise on performance. It boasts a compact design that makes it easy to maneuver in tight spaces. Its lightweight construction facilitates transport, and it incorporates user-friendly controls that enhance the operational experience for farmers. The P300's efficient spraying system reduces drift, ensuring that chemicals are applied exactly where needed, thus protecting the surrounding environment.

Moving onto the P600 model, this sprayer is engineered for large-scale agricultural operations. It features an extensive range of customizable options that cater to specific farming needs. The P600's robust build is complemented by powerful engines that ensure reliability even in demanding conditions. Additionally, it incorporates state-of-the-art GPS and automated guidance systems, allowing for precise inter-row spraying and reducing overlap—this significantly improves efficiency and decreases operational costs.

Lastly, the Unigreen P500 bridges the gap between the P400 and P600, offering advanced technology in a slightly smaller package. One of its standout characteristics is the innovative boom design that provides exceptional stability in various terrains. The sprayer includes advanced monitoring systems that track performance metrics in real-time, enabling farmers to make informed decisions while in the field.

Overall, the Unigreen P series sprayers are distinguished by their user-centric designs, technological advancements, and high-performance capabilities. Their commitment to sustainability and efficiency makes them an excellent investment for progressive farming operations looking to enhance productivity and optimize resource use. Unigreen continues to innovate, ensuring that their products remain at the forefront of agricultural technology.