Land Pride OS1572, OS1548 manual Tractor Requirements, Pre-Assembly Checklist, Sling Brackets

Page 11

Land Pride

Table of Contents

Section 1: Assembly & Set-up

Tractor Requirements

Weight & Horsepower

Tractor horsepower should be within the range noted below. Tractors outside the horsepower range must not be used.

Horsepower Rating. . . . . . . . . . . . . . . . . . . 25-60 HP

3-Point Hitch Type . . . . . . . . . . . . . . . . . . . . . . . Cat. I

Rear PTO Speed . . . . . . . . . . . . . . . . . . . . .540 RPM

Tractor Weight . . . . . . . . . See Important Note Below

IMPORTANT: Ballast may need to be added to your tractor to maintain steering control. Refer to your tractor’s operator manual to determine if additional ballast is needed.

Shipping information

Your Overseeder is shipped partly assembled via flat bed truck. It is the responsibility of the dealer to unload and assemble the Overseeder.

Unload all equipment before beginning assembly. Do not attempt any assembly work while Overseeder is on the truck.

Read and understand the previous section, “Important Safety Information” page 1, before starting assembly.

Pre-Assembly Checklist

The information in the Pre-Assembly Checklist is general in nature and was written to aid the operator in preparing of the tractor and Overseeder for use, and to provide general operating procedures. The operator’s experience, familiarity with the machine, and the following information combined should provide efficient Overseeder operation and good working habits.

Having all the parts and equipment readily at hand will speed your assembly task and make the job as safe as possible. Please review Pre-Assembly Checklist now.

Sling Brackets

Refer to Figure 1-1:

After the unit is uncrated, check to see if the sling brackets (#1) are installed, if not, install one on each end of unit now with 1/2” x 1” long bolts (#2), 1/2” lock washer (#3) and 1/2” hex nut (#4). The sling brackets allow points at each end to hook the chain for lifting of the unit.

NOTE: When hooking hoist chain to sling brackets, be certain to either use a spreader bar on the chain or use a long chain to prevent bending sling brackets.

Pre-Assembly Checklist

Check

Reference

Make sure miscellaneous assembly tools are on hand: Hammer, tape measure, hacksaw, assortment of wrenches & sockets, 3/8" drill, drill bits and spirit level.

Have a forklift or hoist with properly sized chains and safety stands on hand capable of lifting 2000 lbs.

Have a minimum of two people available during assembly. See Specifications on page 44 for unit weights.

Check to see if auxiliary tractor weights are needed.

Make sure all major components and loose parts

Operator’s

are shipped with the machine.

Manual

 

 

Double check to make sure all fasteners & pins

Operator’s

are installed in the correct location. Refer to the

& Parts

Parts Manual if unsure.

Manual

NOTE: All assembled hardware from the factory

 

has been installed in the correct location.

 

Remember location of a part or fastener if

 

removed during assembly. Keep parts separated.

 

Make sure working parts move freely, bolts are

Operator’s

tight & cotter pins are spread.

Manual

Make sure all grease fittings are in place and

Section 4

lubricated.

Page 31

Make sure gearbox is filled with gear lube as

Section 4

indicated in “Lubrication Points”.

Page 38

Make sure all drive chains are properly tension

Operator’s

and aligned.

Manual

Make sure all safety labels are correctly located

Safety Labels

and legible. Replace if damaged.

Page 4

Make sure all tires are inflated to the specified

Section 9

psi air pressure.

Page 48

Make sure all wheel bolts and axle nuts are

Section 9

tightened to the specified torque.

Page 48

 

 

Torque Requirements

Refer to “Torque Values Chart” on page 48 to determine correct torque values when tightening hardware.

14588

Sling Bracket Installation

Figure 1-1

2-16/09

OS1548 and OS1572 Overseeder (S/N 166724+) 308-303M

9

Image 11
Contents Overseeder S/N 166724+ Table of Contents Safety at All Times Transport Machinery Safely Use Safety Lights and DevicesUse a Safety Chain Practice Safe MaintenanceAvoid High Pressure Fluids Hazard Prepare for EmergenciesWear Protective Equipment Keep Riders Off Machinery818-540C 818-055C818-552C 818-129C 818-130C 818-132C 838-111C 818-858C818-543C Owner Assistance Using This ManualApplication Further Assistance Land Pride Service Department East North StreetTorque Requirements Pre-Assembly ChecklistTractor Requirements Sling BracketsRotor to Overseeder Installation-Left Hand Side Gauge Wheel Drive DisassemblyBearing Mount Plate & Rotor Assembly RH Side Rotor to Overseeder Assembly RH SideRear Roller Drive Rear Roller AssemblyGauge Wheel Drive Maximum PTO driveline Movement During Operation Driveline InstallationCheck Driveline Minimum Length Long Arm Chain Guard LocationPTO Driveline Shortening Check Driveline Maximum LengthCheck Operating ChecklistOperating Check List Tractor Hook-UpTransporting Filling the Seed Box Parking How the Seeder WorksGeneral Notes for Field Operations General Operating Instructions Coverage= 1000 Sq. Ft Acre Model No Wheel Roller Seeding AdjustmentsNumber of Gauge Wheel & Rear Roller Rotations Gauge wheel drive units Raise and supportDrive Sprocket Arrangements Gauge Wheel DriveRear Roller Drive Drive Sprocket AlignmentsFescue Fine Blade, Turf Type Pounds per 1000 Square Feet Seed Rate Charts EnglishFescue Fine Blade, Turf Type Pounds per Acre Small Seeds Attachment Seed Rate Chart Fescue Fine Blade, Turf Type Kilograms per Hectare Seed Rate Charts MetricLovegrass Sand Kilograms per 1000 Square Meters Rear Roller Drive Rotary Cutting Depth AdjustmentGauge Wheel Drive Floating Top Link Floating Top Link AdjustmentFront Roller Turnbuckle Rear Roller Drive w/Front RollerTine Attachment Optional Rear Arm Length AdjustmentTo adjust height of tines To adjust angle of tinesRotor Drive Chain Adjustment Feed Cup Drive System AdjustmentRotor Drive Chain Adjustment Slit Seeder AdjustmentOS1572 161 Small Seeds Drive AdjustmentSmall Seeds Attachment Optional OS1548 22811667 Pounds per 1000 square foot and Pounds per acre Small Seeds Seed Rate Chart EnglishCup Setting Storage MaintenanceIndividual Knife Replacement Rotor MaintenanceRear Roller Drive Disconnect Right Hand Rotor DisassemblyLeft Hand Rotor Disassembly Overseeders With Rear Roller Drive Refer to FigureRear Roller Inspection Rear Roller MaintenanceRear Roller Disassembly Rear Roller AssemblyType C Clutch Run-In Clutch Disassembly, Inspection & AssemblyDriveline Slip Clutches Type a Clutches Clutch Run-InOS1548 2-Plate Assembly Step OS1548 2-Plate Disassembly StepOS1572 4-Plate Assembly Step OS1572 4-Plate Disassembly StepHex Head Socket Bolts Disassembly and AssemblyType B Clutch Assembly Type B Clutch Clutch Run-InSeasonally Lubrication PointsHours Agitator Drive Chain Rear Roller BearingsFeed Cup Drive Sprocket Feed Cup Drive ChainsDrive Sprocket Hanger Bearing RequiredGearbox Driveline ChaincaseRear Tine Attachment Slit Seeder AttachmentRear Tine Attachment Slit Seeder AttachmentFront Roller Attachment Adjustments, onFront Roller Attachment Land Pride Overseeder Size Drive System Adjustments, on Lubrication, on Troubleshooting, onSmall Seeds Attachment Optional Add-on Equipment OS1548 & OS1572 SeriesOS1548 OS1572 26728 OS15 Series Overseeders Features BenefitsProblem Solution Troubleshooting ChartAdditional Torque Values Torque Values ChartTire Inflation Chart Overall Unit and Driveline One year Parts and Labor WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

OS1572, OS1548 specifications

The Land Pride OS1548 and OS1572 are outstanding implements designed to enhance the efficiency and productivity of landscape and turf maintenance. These models are part of Land Pride's lineup of high-quality equipment, built for durability and performance.

One of the main features of the OS1548 and OS1572 is their robust construction. Each model is meticulously crafted using high-strength steel, which gives them a solid framework that can withstand rigorous daily use. This durability is complemented by high-quality welds and a corrosion-resistant finish, ensuring that these implements will serve users well over the years, even in challenging environments.

Both models are equipped with a high-capacity hopper that makes them suitable for all types of seed and fertilizer applications. The OS1548 has a 48-inch working width, while the OS1572 boasts a larger 72-inch width. This variety allows operators to choose a model that best fits their specific needs, whether for residential or commercial use. The ample hopper capacity allows for extended work periods without constant refilling, maximizing efficiency and minimizing downtime.

The OS1548 and OS1572 come with a unique broadcasting system that ensures even distribution of seeds and fertilizers across the treated area. This is crucial for achieving uniform growth and maximizing the effectiveness of inputs. The finely tuned spread pattern also reduces waste and ensures that materials are used economically.

Another innovative feature of these models is their user-friendly design. They come equipped with adjustable settings that allow operators to easily control the flow rate of the materials being spread. This feature is particularly beneficial for tasks that require precision, such as overseeding or applying specific fertilizers.

Both models are designed for versatility, capable of tackling various landscaping tasks. Whether you're preparing a new lawn, refreshing a garden bed, or maintaining a sports field, the OS1548 and OS1572 deliver exceptional results.

In conclusion, the Land Pride OS1548 and OS1572 are exceptional implements that combine strength, efficiency, and user-friendly features. With their robust construction, high capacity, and precise broadcasting system, they are ideal for anyone looking to enhance their landscaping capabilities. These models exemplify Land Pride's commitment to quality and innovation in turf management equipment.