Land Pride OS1572 Type B Clutch Clutch Run-In, Disassembly and Assembly, Hex Head Socket Bolts

Page 39

Land Pride

Table of Contents

Section 4: Maintenance & Lubrication

Type B Clutch

Clutch Run-In

Refer to Figure 4-10:

1.Loosen counterclockwise all 8 hex head socket bolts uniformly 6 full turns.

2.Cycle clutch on and off 5 or 6 times (15 seconds on and 15 seconds off) with the engine operating at half throttle. Disengage driveline, shut off tractor and remove key. Wait for all components to stop before dismounting from tractor.

3.Tighten hex head socket bolts fully back. Clutch is ready for use

4.The clutch should be checked during the first hour of cutting and periodically each week.

Hex Head

Socket Bolts

(IMPORTANT NOTICE) Check position of lip on stop flange (UP or DOWN). Replace stop flange with lip in its original position.

21270

Type B Clutch Run-In

Figure 4-10

Disassembly and Assembly

Refer to Figure 4-11:

If the clutch run-in procedure indicated that one or more of the friction disks did not slip, then the clutch must be disassembled to separate the friction disks.

1. Rotate 8 hex head socket bolts (#2) all the way out to free stop flange (#3).

2. Rotate stop flange (#3) and remove from housing (#11)

3. Remove the following inner components:

a. Spring kit (#4)

21302

b. Pressure flange (#5)

c. 1st Friction Disc (#6)

d. Hub with flange and pull collar (#7 & #1) e. 2nd Friction disc (#6)

f. Intermediate flange (#8) g. 3rd Friction disc (#6) h. Hub disc (#9)

i. 4th Friction disc (#6) j. Bearing (#10)

4.

Inspect all components and replace to their original

22376

 

position. Make certain stop flange (#3) is replaced

Type B Clutch Assembly

 

with its flanges down as shown.

 

Figure 4-11

5.

Fully tighten all 8 hex head socket bolts (#2).

 

2-16/09

OS1548 and OS1572 Overseeder (S/N 166724+) 308-303M

37

Image 39
Contents Overseeder S/N 166724+ Table of Contents Safety at All Times Transport Machinery Safely Use Safety Lights and DevicesUse a Safety Chain Practice Safe MaintenanceAvoid High Pressure Fluids Hazard Prepare for EmergenciesWear Protective Equipment Keep Riders Off Machinery818-055C 818-552C818-540C 818-129C 818-130C 818-132C 818-858C 818-543C838-111C Using This Manual ApplicationOwner Assistance Further Assistance Land Pride Service Department East North StreetTorque Requirements Pre-Assembly ChecklistTractor Requirements Sling BracketsRotor to Overseeder Installation-Left Hand Side Gauge Wheel Drive DisassemblyBearing Mount Plate & Rotor Assembly RH Side Rotor to Overseeder Assembly RH SideRear Roller Assembly Gauge Wheel DriveRear Roller Drive Maximum PTO driveline Movement During Operation Driveline InstallationCheck Driveline Minimum Length Long Arm Chain Guard LocationPTO Driveline Shortening Check Driveline Maximum LengthCheck Operating ChecklistOperating Check List Tractor Hook-UpTransporting Filling the Seed Box How the Seeder Works General Notes for Field OperationsParking General Operating Instructions Coverage= 1000 Sq. Ft Acre Model No Wheel Roller Seeding AdjustmentsNumber of Gauge Wheel & Rear Roller Rotations Gauge wheel drive units Raise and supportDrive Sprocket Arrangements Gauge Wheel DriveRear Roller Drive Drive Sprocket AlignmentsSeed Rate Charts English Fescue Fine Blade, Turf Type Pounds per AcreFescue Fine Blade, Turf Type Pounds per 1000 Square Feet Small Seeds Attachment Seed Rate Chart Fescue Fine Blade, Turf Type Kilograms per Hectare Seed Rate Charts MetricLovegrass Sand Kilograms per 1000 Square Meters Rotary Cutting Depth Adjustment Gauge Wheel DriveRear Roller Drive Floating Top Link Floating Top Link AdjustmentFront Roller Turnbuckle Rear Roller Drive w/Front RollerTine Attachment Optional Rear Arm Length AdjustmentTo adjust height of tines To adjust angle of tinesRotor Drive Chain Adjustment Feed Cup Drive System AdjustmentRotor Drive Chain Adjustment Slit Seeder AdjustmentOS1572 161 Small Seeds Drive AdjustmentSmall Seeds Attachment Optional OS1548 22811667 Small Seeds Seed Rate Chart English Cup SettingPounds per 1000 square foot and Pounds per acre Storage MaintenanceIndividual Knife Replacement Rotor MaintenanceRear Roller Drive Disconnect Right Hand Rotor DisassemblyLeft Hand Rotor Disassembly Overseeders With Rear Roller Drive Refer to FigureRear Roller Inspection Rear Roller MaintenanceRear Roller Disassembly Rear Roller AssemblyType C Clutch Run-In Clutch Disassembly, Inspection & AssemblyDriveline Slip Clutches Type a Clutches Clutch Run-InOS1548 2-Plate Assembly Step OS1548 2-Plate Disassembly StepOS1572 4-Plate Assembly Step OS1572 4-Plate Disassembly StepHex Head Socket Bolts Disassembly and AssemblyType B Clutch Assembly Type B Clutch Clutch Run-InLubrication Points HoursSeasonally Agitator Drive Chain Rear Roller BearingsFeed Cup Drive Sprocket Feed Cup Drive ChainsDrive Sprocket Hanger Bearing RequiredGearbox Driveline ChaincaseRear Tine Attachment Slit Seeder AttachmentRear Tine Attachment Slit Seeder AttachmentAdjustments, on Front Roller AttachmentFront Roller Attachment Adjustments, on Lubrication, on Troubleshooting, on Small Seeds AttachmentLand Pride Overseeder Size Drive System OS1548 & OS1572 Series OS1548 OS1572Optional Add-on Equipment 26728 OS15 Series Overseeders Features BenefitsProblem Solution Troubleshooting ChartTorque Values Chart Tire Inflation ChartAdditional Torque Values Overall Unit and Driveline One year Parts and Labor WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

OS1572, OS1548 specifications

The Land Pride OS1548 and OS1572 are outstanding implements designed to enhance the efficiency and productivity of landscape and turf maintenance. These models are part of Land Pride's lineup of high-quality equipment, built for durability and performance.

One of the main features of the OS1548 and OS1572 is their robust construction. Each model is meticulously crafted using high-strength steel, which gives them a solid framework that can withstand rigorous daily use. This durability is complemented by high-quality welds and a corrosion-resistant finish, ensuring that these implements will serve users well over the years, even in challenging environments.

Both models are equipped with a high-capacity hopper that makes them suitable for all types of seed and fertilizer applications. The OS1548 has a 48-inch working width, while the OS1572 boasts a larger 72-inch width. This variety allows operators to choose a model that best fits their specific needs, whether for residential or commercial use. The ample hopper capacity allows for extended work periods without constant refilling, maximizing efficiency and minimizing downtime.

The OS1548 and OS1572 come with a unique broadcasting system that ensures even distribution of seeds and fertilizers across the treated area. This is crucial for achieving uniform growth and maximizing the effectiveness of inputs. The finely tuned spread pattern also reduces waste and ensures that materials are used economically.

Another innovative feature of these models is their user-friendly design. They come equipped with adjustable settings that allow operators to easily control the flow rate of the materials being spread. This feature is particularly beneficial for tasks that require precision, such as overseeding or applying specific fertilizers.

Both models are designed for versatility, capable of tackling various landscaping tasks. Whether you're preparing a new lawn, refreshing a garden bed, or maintaining a sports field, the OS1548 and OS1572 deliver exceptional results.

In conclusion, the Land Pride OS1548 and OS1572 are exceptional implements that combine strength, efficiency, and user-friendly features. With their robust construction, high capacity, and precise broadcasting system, they are ideal for anyone looking to enhance their landscaping capabilities. These models exemplify Land Pride's commitment to quality and innovation in turf management equipment.