Land Pride OS1548, OS1572 manual Quick Change Rotor, Gauge Wheel Drive Disassembly

Page 12

Table of Contents

Section 1: Assembly & Set-up

Land Pride

Quick Change Rotor

Attach a chain, cable or lifting strap to the two Overseeder sling brackets. Use an overhead hoist for the rotor installation. Raise Overseeder.

Refer to Figure 1-2:

Complete steps 1 to 4 if your Overseeder comes equipped with a gauge wheel drive. Skip to step 5 if it does not have gauge wheels.

1.Remove chain cover (#1) on the right hand side by removing 1/4” x 1/2” long bolts (#2).

2.Disconnect right hand spring loaded gauge wheel link (#3) from the right hand gauge wheel arm (#4) by removing 5/8” x 2 1/2” long bolt (#5) and 5/8” nut (#6).

3.Remove drive wheel chain.

4.Remove cotter pin (#7) that retains the right hand gauge wheel arm and remove gauge wheel arm assembly. Be careful not to loose any components.

Refer to Figure 1-3:

5.Remove right hand bearing mount plate (#1) from Overseeder main frame.

6.Separate right hand bearing cover (#2) from right hand bearing mount plate (#1).

7.Between these two parts (#1 & #2) are two bearing mount gaskets (#4). Place one of these bearing mount gaskets between the bearing mount (#3) and the bearing mount plate (#1).

8.Then place the other bearing mount gasket between bearing mount plate (#1) and bearing cover (#2).

9.Retain these parts with 1/2” x 1 3/4” long bolts (#5), 1/2” lock washers (#6) and 1/2” hex nuts (#7). Hand tighten nuts at this time. Final torquing of these bolts will be later in the assembly process.

10.Check to make sure set screws in the hub inside the bearing mount (#3) are loose so it is free to rotate on the rotor shaft.

Refer to Figure 1-4:

11.Lift Overseeder high enough to roll rotor into position under the Overseeder frame.

12.With rotor properly positioned, slowly lower Overseeder making sure the right hand bearing mount plate (#1) is to the outside of the right hand frame end panel.

Refer to Figure 1-5:

13.Connect rotor to rotor drive hub (#1) on the left hand side using 7/16” x 1” long bolts (#3) and 7/16” lock washer (#2). Leave bolts loose.

Refer to Figure 1-4:

14.Connect right hand bearing mount plate to the Overseeder main frame using 1/2” x 1 1/4” bolt (#2), 1/2” lock washer (#3) and 1/2” hex nut (#4). Draw nuts up snug, do not tighten.

14594

Gauge Wheel Drive Disassembly

Figure 1-2

14592

Bearing Mount Plate & Rotor Assembly (RH Side)

Figure 1-3

14703

Rotor to Overseeder Assembly (RH Side)

Figure 1-4

14645

Rotor to Overseeder Installation-Left Hand Side

Figure 1-5

10 OS1548 and OS1572 Overseeder (S/N 166724+) 308-303M

2-16/09

Image 12
Contents Overseeder S/N 166724+ Table of Contents Safety at All Times Use Safety Lights and Devices Use a Safety ChainPractice Safe Maintenance Transport Machinery SafelyPrepare for Emergencies Wear Protective EquipmentKeep Riders Off Machinery Avoid High Pressure Fluids Hazard818-055C 818-552C818-540C 818-129C 818-130C 818-132C 818-858C 818-543C838-111C Using This Manual ApplicationOwner Assistance Land Pride Service Department East North Street Further AssistancePre-Assembly Checklist Tractor RequirementsSling Brackets Torque RequirementsGauge Wheel Drive Disassembly Bearing Mount Plate & Rotor Assembly RH SideRotor to Overseeder Assembly RH Side Rotor to Overseeder Installation-Left Hand SideRear Roller Assembly Gauge Wheel DriveRear Roller Drive Driveline Installation Check Driveline Minimum LengthLong Arm Chain Guard Location Maximum PTO driveline Movement During OperationCheck Driveline Maximum Length PTO Driveline ShorteningOperating Checklist Operating Check ListTractor Hook-Up CheckTransporting Filling the Seed Box How the Seeder Works General Notes for Field OperationsParking General Operating Instructions Seeding Adjustments Number of Gauge Wheel & Rear Roller RotationsGauge wheel drive units Raise and support Coverage= 1000 Sq. Ft Acre Model No Wheel RollerGauge Wheel Drive Rear Roller DriveDrive Sprocket Alignments Drive Sprocket ArrangementsSeed Rate Charts English Fescue Fine Blade, Turf Type Pounds per AcreFescue Fine Blade, Turf Type Pounds per 1000 Square Feet Small Seeds Attachment Seed Rate Chart Seed Rate Charts Metric Fescue Fine Blade, Turf Type Kilograms per HectareLovegrass Sand Kilograms per 1000 Square Meters Rotary Cutting Depth Adjustment Gauge Wheel DriveRear Roller Drive Floating Top Link Adjustment Front Roller TurnbuckleRear Roller Drive w/Front Roller Floating Top LinkRear Arm Length Adjustment To adjust height of tinesTo adjust angle of tines Tine Attachment OptionalFeed Cup Drive System Adjustment Rotor Drive Chain AdjustmentSlit Seeder Adjustment Rotor Drive Chain AdjustmentSmall Seeds Drive Adjustment Small Seeds Attachment OptionalOS1548 228 OS1572 16111667 Small Seeds Seed Rate Chart English Cup SettingPounds per 1000 square foot and Pounds per acre Maintenance Individual Knife ReplacementRotor Maintenance StorageRight Hand Rotor Disassembly Left Hand Rotor DisassemblyOverseeders With Rear Roller Drive Refer to Figure Rear Roller Drive DisconnectRear Roller Maintenance Rear Roller DisassemblyRear Roller Assembly Rear Roller InspectionClutch Disassembly, Inspection & Assembly Driveline Slip ClutchesType a Clutches Clutch Run-In Type C Clutch Run-InOS1548 2-Plate Disassembly Step OS1548 2-Plate Assembly StepOS1572 4-Plate Disassembly Step OS1572 4-Plate Assembly StepDisassembly and Assembly Type B Clutch AssemblyType B Clutch Clutch Run-In Hex Head Socket BoltsLubrication Points HoursSeasonally Rear Roller Bearings Feed Cup Drive SprocketFeed Cup Drive Chains Agitator Drive ChainRequired GearboxDriveline Chaincase Drive Sprocket Hanger BearingSlit Seeder Attachment Rear Tine AttachmentSlit Seeder Attachment Rear Tine AttachmentAdjustments, on Front Roller AttachmentFront Roller Attachment Adjustments, on Lubrication, on Troubleshooting, on Small Seeds AttachmentLand Pride Overseeder Size Drive System OS1548 & OS1572 Series OS1548 OS1572Optional Add-on Equipment 26728 Features Benefits OS15 Series OverseedersTroubleshooting Chart Problem SolutionTorque Values Chart Tire Inflation ChartAdditional Torque Values Warranty Overall Unit and Driveline One year Parts and LaborCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

OS1572, OS1548 specifications

The Land Pride OS1548 and OS1572 are outstanding implements designed to enhance the efficiency and productivity of landscape and turf maintenance. These models are part of Land Pride's lineup of high-quality equipment, built for durability and performance.

One of the main features of the OS1548 and OS1572 is their robust construction. Each model is meticulously crafted using high-strength steel, which gives them a solid framework that can withstand rigorous daily use. This durability is complemented by high-quality welds and a corrosion-resistant finish, ensuring that these implements will serve users well over the years, even in challenging environments.

Both models are equipped with a high-capacity hopper that makes them suitable for all types of seed and fertilizer applications. The OS1548 has a 48-inch working width, while the OS1572 boasts a larger 72-inch width. This variety allows operators to choose a model that best fits their specific needs, whether for residential or commercial use. The ample hopper capacity allows for extended work periods without constant refilling, maximizing efficiency and minimizing downtime.

The OS1548 and OS1572 come with a unique broadcasting system that ensures even distribution of seeds and fertilizers across the treated area. This is crucial for achieving uniform growth and maximizing the effectiveness of inputs. The finely tuned spread pattern also reduces waste and ensures that materials are used economically.

Another innovative feature of these models is their user-friendly design. They come equipped with adjustable settings that allow operators to easily control the flow rate of the materials being spread. This feature is particularly beneficial for tasks that require precision, such as overseeding or applying specific fertilizers.

Both models are designed for versatility, capable of tackling various landscaping tasks. Whether you're preparing a new lawn, refreshing a garden bed, or maintaining a sports field, the OS1548 and OS1572 deliver exceptional results.

In conclusion, the Land Pride OS1548 and OS1572 are exceptional implements that combine strength, efficiency, and user-friendly features. With their robust construction, high capacity, and precise broadcasting system, they are ideal for anyone looking to enhance their landscaping capabilities. These models exemplify Land Pride's commitment to quality and innovation in turf management equipment.