Land Pride APS1560 Front Roller Angle Adjustment, Mud Scraper Adjustment Optional, Adjustments

Page 16

Table of Contents

Section 3: Adjustments

Front Roller Angle Adjustment

Refer to Figure 3-1:

NOTE: Gang slide (#1) is shown in its furthest back position. In this position, both bent pins (#6) are in front of the gang slide as shown. In all other positions, one bent pin is in back of the gang slide and the other is in front of the gang slide.

1.Lower seeder frame onto blocks supporting the front rollers just above ground level to allow the front rollers to move freely.

2.Shut tractor engine off and engage parking brake.

3.Remove bent pins (#6) and operate roller angling lever (#3) to reposition front rollers (#2) to the desired angle.

4.Replace bent pins (#6) with one on each side of gang slide (#1). Secure bent pins with hair pin cotters (#5).

5.Remove support blocks and lower seeder to ground level.

IMPORTANT: If 1" hex flange lock nuts (#4) have been loosened, they should be retightened until they make contact with gang slide (#1) and then backed off 1/3 revolution (2 hex flats). Some additional backing off of the nuts may be necessary to allow the gang slide to move easily when adjusting roller angle with lever (#3).

24940

Front Roller Adjustment

(Gang Slide #1 Shown Positioned Fully Back)

Figure 3-1

Mud Scraper Adjustment (Optional)

Refer to “Torque Values Chart For Common Bolt Size” on page 28 when tightening hardware.

Refer to Figure 3-2:

Front Mud Scrapers

1.Loosen 3/8"-16 hex nuts (#1 & #2) at both ends of the left front mud scraper (#3).

2.Rotate teeth of mud scraper towards the front roller to increase removal of mud and debris and away if scraper teeth are interfering with the roller.

3.Retighten the four 3/8"-16 GR5 hex head bolts and nuts (#1 & #2) to the proper torque.

4.Repeat steps 1, 2 & 3 above for the right front mud scraper.

Rear Mud Scrapers

1.Loosen 3/8"-16 hex nuts (#4 & #5) at both ends of the rear mud scraper (#6).

2.Rotate teeth of mud scraper towards the front roller to increase removal of mud and debris and away if scraper teeth are interfering with the roller.

3.Retighten the four 3/8"-16 GR5 hex head bolts and nuts (#4 & #5) to the proper torque.

Special Instructions for Spike Rollers

1.With front and rear spike rollers off the ground, loosen round head square neck bolts (#7) and adjust front and rear scrapers left or right to align slots up with the roller spikes. Rotate spike rollers one or more revolutions to verify spikes are not touching the scraper teeth.

2.Tighten front and rear 3/8"-16 x 1 1/4" GR5 bolts (#7) to the correct torque.

 

7

 

6

1

67

 

 

4

2

 

 

3

25608

5

 

Mud Scraper Adjustments

Figure 3-2

14 APS1548, APS1560, APS1572 & APS1586 All Purpose Seeder 313-354M

5/13/08

Image 16
Contents APS1586 24932 APS1548Table of Contents Safety at All Times Practice Safe Maintenance Use a Safety ChainTransport Machinery Safely Tire Safety Wear Protective EquipmentAvoid High Pressure Fluids Hazard Keep Riders Off MachinerySafety Labels 838-111C 818-543C 818-254CUsing This Manual ApplicationOwner Assistance IntroductionPre-Assembly Checklist Assembly & Set-upTractor Requirements Sling BracketMud Scraper Installation Optional Land Pride Mud ScrapersFront Mud Scrapers Rear Mud ScraperRear Mud Scraper Installation to Packer Roller Roller Arm Disassembly PositionSpecial Instructions For Packer Roller Rear Mud Scraper Installation to Spike Roller Special Instructions For Spike RollerOperating Check List TransportingTractor Hook-up Filling the Seed BoxOperating the Seeder How the Seeder WorksSeed Box With Lid Open Parking the Seeder General Operating InstructionsFront Roller Angle Adjustment Mud Scraper Adjustment OptionalAdjustments Rear Mud ScrapersDrive Chain Engagement Disengage Drive ChainSpeed Change Sprocket High Range Set-upLow Range Set-up 35T SprocketSeeding Adjustments Model Rear Roller Rotations to Cover 1000 Sq. Ft AcreFescue Fine Blade, Turf Type Pounds per Acre Seed Rate Charts EnglishFescue Fine Blade, Turf Type Pounds per 1000 Square Feet Lovegrass Sand Pounds per Acre Rye Grass Annual Pounds per AcreRye Grass Perennial Pounds per Acre Wheatgrass Crested Pounds per AcreSeed Rate Charts Metric Fescue Fine Blade, Turf Type Kilograms per HectareLovegrass Weeping Kilograms per 1000 Square Meters Maintenance Cleaning and StoringMaintenance & Lubrication Roller ChainsLand PrideTable of Contents Rear Roller Bearings RequiredRoller Chains APS1548 & APS1572 All Purpose Seeder Specifications & CapacitiesDescription APS1548 APS1560 APS1572 APS1586 Features Benefits Features and BenefitsAPS1548, APS1560, APS1572 & APS1586 Models Troubleshooting Chart TroubleshootingProblem Cause Torque Values Chart For Common Bolt Size AppendixAdditional Torque Values In-tpiWarranty Front & Rear Rollers Considered wear itemsCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

APS1548, APS1586, APS1572, APS1560 specifications

Land Pride, a well-known name in agricultural and landscape equipment, offers a range of premium tillers designed to enhance productivity and performance in various farming and landscaping applications. Among their impressive lineup, the APS1548, APS1586, APS1560, and APS1572 models stand out due to their robust features and user-friendly technologies.

The APS1548, with a width of 48 inches, is an ideal choice for smaller gardens or compact tractors. It provides exceptional performance in tilling and soil preparation, helping to create a fertile foundation for planting. Equipped with heavy-duty tines, the APS1548 ensures efficient soil penetration, breaking up tough ground and turning it over with ease.

Moving up in size, the APS1560 boasts a working width of 60 inches, making it suitable for medium-sized tractors and larger areas. It offers similar heavy-duty construction, with reinforced tines capable of handling various soil types. The APS1560 is designed for precision and reliability, ensuring that your planting beds are thoroughly prepared for optimal crop growth.

The APS1572 takes it a step further with its 72-inch wide working area, ideal for larger fields and more intensive farming operations. Its increased coverage means less time spent tilling and more efficient operation. This model excels in durability, featuring a robust frame and high-quality components that ensure longevity, even under tough working conditions.

The APS1586, at 86 inches wide, is targeted towards large-scale farmers and landscapers who demand high efficiency. This model can cover extensive areas quickly and effectively, making it a perfect choice for commercial operations. It integrates advanced technologies, such as quick-hitch compatibility, allowing for easy attachment and detachment to maximize productivity.

All models feature adjustable tilling depths, enabling users to tailor their operation to specific soil conditions. Additionally, the tines can be easily replaced, providing extended service life and reducing maintenance costs. Land Pride’s commitment to quality is evident in the construction of these tillers, ensuring they withstand the rigors of daily use while providing consistent performance.

In summary, the Land Pride APS series—comprising the APS1548, APS1586, APS1560, and APS1572—represents a strong lineup of tillers that cater to a variety of agricultural needs. Their robust construction, user-friendly design, and thoughtful features make them a valuable investment for farmers and landscapers seeking to improve their productivity and soil health.