Land Pride APS1548 Seeding Adjustments, Model Rear Roller Rotations to Cover 1000 Sq. Ft Acre

Page 19

Land Pride

Section 3: Adjustments

Table of Contents

Seeding Adjustments

1.Use seed rate charts beginning on page 18 to determine correct seeding rate. Make adjustments as follows:

a.Decide whether your drive needs to be set-up for low range or high range. If necessary, change the speed change sprocket to accommodate the correct speed range. See “Speed Change Sprocket” on page 16.

Refer to Figure 3-6:

IMPORTANT: Use seed rate charts as a guide. There are many factors which will affect seeding rates: seed treatment, weight of seed, soil surface condition and rear roller slippage. Minor adjustments to the seed rate handle may be needed to compensate for these factors.

b.Locate seed rate adjustment lever at rear of seeder and move it to indicator number obtained from the seed rate charts. For best results, first move adjustment lever all the way to the left. Then move lever to desired setting, moving from a lower to a higher number.

•Increase seed rate setting if the seed is lighter than average.

•Decrease seed rate setting if seed is heavier than average.

2.Complete the following procedure to calibrate dispersal rate for your specific seed.

a.Place several pounds of seed over three of the seed cups at the outboard end of the seeder. Do not allow any of the seed to reach other cups.

b.Lower seeder frame onto blocks supporting rear roller just above ground level to allow roller to turn freely.

NOTE: Rotate rear roller by grasping the roller and pulling away from the seeder at the bottom of the roller and pushing toward the seeder at the top.

c.Rotate rear roller to make sure drive system is working properly and seed cups are free from foreign matter.

d.Place a drop cloth under the seeder to collect all seeds that are metered out.

e.Be sure to check the three seed cups to make sure each cup has plenty of seed falling into it and no other cups are receiving seed.

f.Rotate rear roller as noted in table below.

Model

Rear Roller Rotations to Cover

No

1000 Sq. Ft.

 

1/10 ACRE

 

 

 

APS1548

103 rotations

 

450 rotations

 

 

 

 

APS1560

89 rotations

 

388 rotations

 

 

 

 

APS1572

73 rotations

 

319 rotations

 

 

 

 

APS1586

61 rotations

 

266 rotations

 

 

 

 

g.Weigh the seed which has been metered out and divide that weight by three to get the number of pounds metered by each seed cup. If your weight is in ounces, divide the weight by 48 to get the number of pounds metered by each seed cup.

h.Next, multiply number of pounds per cup by number of cups on your seeder to arrive at total pounds per 1000 sq. ft. or pounds per 1/10 acre.

i.If calculations are based on 1/10 acre, multiply total pounds by 10 to arrive at total pounds per acre.

j.If this figure (total pounds) is different than desired, then readjust your seed cup adjustment lever accordingly.

3.You may want to repeat calibration procedure if results of your calibration vary greatly from suggested settings on the chart.

NOTE: To determine seed rates for seeds not listed on the charts, compare weight and size to those listed in the seed rate charts and use a similar setting.

Follow steps 4 and 5 to calibrate seed rate.

IMPORTANT: Remember, field conditions will affect seeding rates. When seeding, check amount of seed you are using by noting acres or square feet seeded, amount of seed added to seeder, and level of seed in the seed box. You may need to adjust the seeding rate slightly to compensate for field conditions if you suspect that you are seeding more or less seed than desired; and you have accurately calibrated the seeder for your seed.

IMPORTANT: This seeder is equipped with a four- position door on each seed cup. The highest handle position is for small seeds, the second and third positions are for larger seeds. Grass seed applications usually require the highest position.

MAKE SURE all handles are in the same position before seeding. The wide open position (lowest position) will allow complete clean out of seed cup.

24937

Seed

Cup

Four-Position

Seed Rate Adjustment Lever

Door Handle

DO NOT open cups to the widest position with seed in the box unless complete clean out is desired.

Seed Rate Adjustment Handle

Figure 3-6

5/13/08

APS1548, APS1560, APS1572 & APS1586 All Purpose Seeder 313-354M

17

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 24932 APS1548 APS1586Table of Contents Safety at All Times Practice Safe Maintenance Use a Safety ChainTransport Machinery Safely Keep Riders Off Machinery Tire SafetyWear Protective Equipment Avoid High Pressure Fluids HazardSafety Labels 818-254C 838-111C 818-543CIntroduction Using This ManualApplication Owner AssistanceSling Bracket Pre-Assembly ChecklistAssembly & Set-up Tractor RequirementsRear Mud Scraper Mud Scraper Installation OptionalLand Pride Mud Scrapers Front Mud ScrapersRear Mud Scraper Installation to Packer Roller Roller Arm Disassembly PositionSpecial Instructions For Packer Roller Special Instructions For Spike Roller Rear Mud Scraper Installation to Spike RollerFilling the Seed Box Operating Check ListTransporting Tractor Hook-upOperating the Seeder How the Seeder WorksSeed Box With Lid Open General Operating Instructions Parking the SeederRear Mud Scrapers Front Roller Angle AdjustmentMud Scraper Adjustment Optional AdjustmentsDisengage Drive Chain Drive Chain Engagement35T Sprocket Speed Change SprocketHigh Range Set-up Low Range Set-upModel Rear Roller Rotations to Cover 1000 Sq. Ft Acre Seeding AdjustmentsFescue Fine Blade, Turf Type Pounds per Acre Seed Rate Charts EnglishFescue Fine Blade, Turf Type Pounds per 1000 Square Feet Wheatgrass Crested Pounds per Acre Lovegrass Sand Pounds per AcreRye Grass Annual Pounds per Acre Rye Grass Perennial Pounds per AcreFescue Fine Blade, Turf Type Kilograms per Hectare Seed Rate Charts MetricLovegrass Weeping Kilograms per 1000 Square Meters Roller Chains MaintenanceCleaning and Storing Maintenance & LubricationLand PrideTable of Contents Rear Roller Bearings RequiredRoller Chains APS1548 & APS1572 All Purpose Seeder Specifications & CapacitiesDescription APS1548 APS1560 APS1572 APS1586 Features Benefits Features and BenefitsAPS1548, APS1560, APS1572 & APS1586 Models Troubleshooting Chart TroubleshootingProblem Cause In-tpi Torque Values Chart For Common Bolt SizeAppendix Additional Torque ValuesFront & Rear Rollers Considered wear items WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

APS1548, APS1586, APS1572, APS1560 specifications

Land Pride, a well-known name in agricultural and landscape equipment, offers a range of premium tillers designed to enhance productivity and performance in various farming and landscaping applications. Among their impressive lineup, the APS1548, APS1586, APS1560, and APS1572 models stand out due to their robust features and user-friendly technologies.

The APS1548, with a width of 48 inches, is an ideal choice for smaller gardens or compact tractors. It provides exceptional performance in tilling and soil preparation, helping to create a fertile foundation for planting. Equipped with heavy-duty tines, the APS1548 ensures efficient soil penetration, breaking up tough ground and turning it over with ease.

Moving up in size, the APS1560 boasts a working width of 60 inches, making it suitable for medium-sized tractors and larger areas. It offers similar heavy-duty construction, with reinforced tines capable of handling various soil types. The APS1560 is designed for precision and reliability, ensuring that your planting beds are thoroughly prepared for optimal crop growth.

The APS1572 takes it a step further with its 72-inch wide working area, ideal for larger fields and more intensive farming operations. Its increased coverage means less time spent tilling and more efficient operation. This model excels in durability, featuring a robust frame and high-quality components that ensure longevity, even under tough working conditions.

The APS1586, at 86 inches wide, is targeted towards large-scale farmers and landscapers who demand high efficiency. This model can cover extensive areas quickly and effectively, making it a perfect choice for commercial operations. It integrates advanced technologies, such as quick-hitch compatibility, allowing for easy attachment and detachment to maximize productivity.

All models feature adjustable tilling depths, enabling users to tailor their operation to specific soil conditions. Additionally, the tines can be easily replaced, providing extended service life and reducing maintenance costs. Land Pride’s commitment to quality is evident in the construction of these tillers, ensuring they withstand the rigors of daily use while providing consistent performance.

In summary, the Land Pride APS series—comprising the APS1548, APS1586, APS1560, and APS1572—represents a strong lineup of tillers that cater to a variety of agricultural needs. Their robust construction, user-friendly design, and thoughtful features make them a valuable investment for farmers and landscapers seeking to improve their productivity and soil health.
Top Page Image Contents