Land Pride 322-215M manual Pull Type Hitch Assembly Optional, Roller Scraper Assembly

Table of Contents

Section 1: Assembly & Set-up

Land Pride

Pull Type Hitch Assembly (Optional)

Refer to “Torque Values Chart For Common Bolt Size” on page 21 when tightening hardware.

Refer to Figure 1-2& Figure 1-3:

1.Chock front and back of rollers to prevent unit from shifting. Support 2" square tube frame up so that the top of the clevis plates are level.

2.Remove support stand (#3) and wire snap lock pin (#1A) from the clevis plates (shipping location).

3.The front two holes in hitch frame (#4) should be shipped from the factory attached to the front holes in the clevis plates with hitch pins (#17) and linch pins (#11). If not, make this pin connection now.

4.Rotate hitch frame (#4) down to align rear holes in hitch frame with holes at the back of the clevis plates. Insert 5/8"-11 x 1 1/2" GR5 carriage bolts (#10) and secure with 5/8" hex flange lock

nuts (#16). Draw nuts up snug, do not tighten.

5.Remove 3/4" hex cap screws (#9), 2" spacer (#2) and and 3/8" cap screws (#8) from hitch frame (#4).

IMPORTANT: The tongue (#5) should be as near level as possible when pulling the roller over soil. Before proceeding, determine which hitch assembly below to use that will mount the tongue near level.

•Use hitch assembly in Figure 1-2to mount tongue (#5) if tractor drawbar is lower than 13"

•Use hitch assembly in Figure 1-3to mount tongue (#5) if tractor drawbar is 13" or higher.

6.Attach tongue (#5) to 3-point hitch (#4) as follows:

a.Remove bolts (#8) from back of tongue (#5).

b.Attach middle of tongue to hitch (#2) with two 3/4"-10 x 3 1/2" GR5 cap screws (#9), one 2" lg. spacer (#2) and two 3/4" flange lock nuts (#14).

c.Attach back of tongue with two 3/8"-16 x 1" GR5 cap screws (#8) and 3/8" flange lock nuts (#15).

7.Tighten flange lock nuts (#14, #15 & #16) to the correct torques.

NOTE: See Figure 1-3.Ball hitch (#6) and clevis hitch (#7) can be installed with either hitch facing forward. Determine which hitch you intend to use and face that hitch forward.

8.Remove wire snap lock pin (#1B). Reorient ball hitch (#6) and clevis hitch (#7) with preferred hitch facing forward and then reattach hitch to tongue (#5) with wire snap lock pins (#1A & 1B).

9.Attach support stand (#3) to wire snap lock pin (#1A). When not in use, rotate stand up and secure in place with second wire snap lock pin (#1B).

10.If clevis hitch (#7) is facing forward, insert 3/4" hitch pin (#12) and secure with hair pin cotter (#13). If ball hitch (#6) is facing forward, store hitch pin and hair pin cotter in a safe location of your choosing.

Roller Scraper Assembly

Refer to “Torque Values Chart For Common Bolt Size” on page 21 when tightening hardware.

Refer to Figure 1-4 on page 9:

1.Attach roller scraper assembly to the Seed Bed Roller frame with 3/8"-16 x 1" GR5 round head square neck bolts (#2) and hex flange lock nuts (#3).

2.Tighten nuts to the correct torque.

3.Some adjustment to the scraper teeth can be made by loosening the nuts on scraper (#1). Retighten nuts after adjustment has been made. See “Scraper Bar Adjustment” on page 11 for detailed instructions.

25774

26518

Pull Type Hitch Assembly	Pull Type Hitch Assembly
With Drawbar 13" & Higher	With Drawbar under 13" High
Figure 1-2	Figure 1-3

8 Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M 2/23/09