Land Pride 322-215M manual Tractor Requirements, Three Point Hitch Assembly, Three-Point Hook-up

Page 9

Land Pride

Table of Contents

Section 1: Assembly & Set-up

Tractor Requirements

The tractor horsepower and weight must be capable of controlling the Seed Bed Roller under all operating conditions. Smaller horsepower and lighter weight tractors must not be used.

Three-Point Hook-up

A Category I hitch with 7/8” dia. holes in the lower hitch links and 3/4” dia. hole in the top link is required. The lower 3-point arms must be stabilized to prevent side-to- side movement. Most tractors have sway blocks or adjustable chains for this purpose. A Category I Land Pride Quick Hitch can be used with the implement.

Horsepower requirements. . . . . . . . . . . . . . .18 - 50 hp. Minimum tractor weight . . . . . . . . . . . . . . . . . . 700 lbs.

Pull Type Hook-Up

The Pull Type Model is set-up with a 2" ball hitch and a clevis type hitch.

Pull-type HP. . . . . . . . . . . . . . . . . . . . . . . . . . 18 - 50 hp.

Three Point Hitch Assembly

Refer to “Torque Values Chart For Common Bolt Size” on page 21 when tightening hardware.

Refer to Figure 1-1:

1.Chock front and back of rollers to prevent unit from shifting while assembling the hitch assembly.

2.Attach support stand (#3) to clevis plate with 5/8" wire snap lock pin (#10). Make certain notch “A” is located against the square tubing corner as shown.

3.Attach bottom of hitch frame (#4) to clevis plates with two 5/8"-11 x 1 1/2" GR5 round head square neck bolts (#6) and 5/8" hex flange lock nuts (#7). Draw nuts up snug, do not tighten.

4.Attach upper two holes in hitch frame to clevis plates with hitch pins (#1) and linch pins (#9)

5.Install 3/4"-10 x 3 1/2" GR5 hex head cap screw (#5A) with 1 1/4" x 2" spacer (#2) and 3/4" hex flange lock nut (#7). Tighten nut to the correct torque.

6.Install 3/4"-10 x 3 1/2" GR5 hex head cap screw (#5B) and 3/4" hex flange lock nut (#8). Draw nut up snug.

7.Tighten 5/8" hex flange lock nuts (#7) to the corrrect torque.

25773

Three point Hitch Assembly

Figure 1-1

2/23/09

Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M

7

Page 8 Page 10
Image 9
Page 8 Page 10
Contents With Pull Hitch Option Without Pull Hitch OptionTable of Contents Safety at All Times Use a Safety Chain Practice Safe MaintenanceTransport Machinery Safely Wear Protective Equipment Tire SafetyAvoid High Pressure Fluids Hazard Keep Riders Off Machinery848-148C Safety LabelsUsing This Manual ApplicationOwner Assistance Further Assistance Land Pride Service Department East North StreetTractor Requirements Three Point Hitch AssemblyThree-Point Hook-up Pull Type Hook-UpRoller Scraper Assembly Pull Type Hitch Assembly OptionalRefer to -5 & Figure Point Hook-UpPull-type Hook-up Clevis Hook-upBall Hook-up Ball Hitch Swivel Adjustment Scraper Bar AdjustmentOperating Checklist Operating Check ListTransporting Operating Instructions Hitch weight when unhookingPoint Type Field Position to Transport PositionStorage Instructions Unhooking the Seed Bed RollerPoint Type Pull TypeGeneral Operating Instructions Lubrication MaintenanceHours Roller Flange BearingsDrag Harrow Additional Seeding EquipmentDisc Harrow Electric Spin SpreaderComplete One Pass Seeding Application Description Three-Point Pull-Type SBR SeriesFeatures Benefits Features and BenefitsAdditional Torque Values Torque Values Chart For Common Bolt SizeIn-tpi · m Ft-lb Mm x pitchTable of Contents Warranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA
Top Page Image Contents