ViewSonic PJ658 Power on/off, Turning on the power, Turning off the power, Blinking in orange

Page 21

Power on/off

Power on/off

WARNING ►When the power is on, a strong light is emitted. Do not look into the lens of projector. Also do not peep at the inside of projector through a hole.

NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices. Power off the projector later than the connected devices.

Turning on the power

1. Make sure that the power cord is firmly and cor- rectly connected to the projector and the outlet.

2. Remove the lens cover, and set the power switch to the ON position.

The power indicator will light up in steady orange. Then wait several seconds because the buttons may not func- tion for these several seconds.

STANDBY/ON button

POWER indicator

(1)When AUTO ON in the OPTION menu is set to TURN ON: The lamp will only be automatically turned on when the Power switch is turned on after the power was turned off by Power switch last time. Afterwards the POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in green.

(2)When AUTO ON in the OPTION menu is set to TURN OFF please see step 3.

3.Press the STANDBY/ON button on the projector or the re- mote control.

To display the picture, select an input signal according to the sec- tion "Selecting an input signal".

Turning off the power

Please pay special attention to below two points when you do:

POWER

(Steady orange)

POWER (Blinking in green) POWER (Steady green)

(1)Please do not turn the projector on again for at least 10 minute in this case. Neglect could shorten the lifetime of the lamp.

(2)During use or immediately after use, do not touch around the lamp and vents of the

1.projector It could cause a burn.Press the STANDBY/ON button on the projector or the remote control.

The message "Power off?" will appear on the screen for about 5

seconds.

Power off?

 

Press the STANDBY/ON button on the projector or the remote

 

2. control again while the message appears.

POWER

The projector lamp will go off, and the POWER indicator will begin

(Blinking in orange)

blinking in orange.

 

Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete.

3. Make sure that the power indicator lights in steady orange, and set the power switch to the OFF position. The POWER indicator will

go off. Attach the lens cover.

POWER (Steady orange)

ViewSonic

PJ658

17

Image 21
Contents ViewSonic Compliance Information Important Safety Instructions Product Registration For Your Records Copyright InformationAbout this manual Contents of packageContent About contents of package Fastening the lens cover Projector Part namesComponent CB/PBCR/PR Remote control Control buttonsMagnify Setting up Min Max Down ArrangementElevator feet Elevator button Adjusting the projectors elevatorUsing the Security Bar How to attachSecurity Bar Anti-theft chain or wire sold separately About Plug-and-Play capability Connecting your devicesConnecting to a speaker with amplifier output Connecting to a monitor outputExamples of connection with a computer RS-232C USBExamples of connection with a VCR/DVD player CB/PBCR/PR AC inlet Connector Power cord Connecting power supplyPutting batteries Remote controlTion Menu Using the remote controlTurning on the power Power on/offTurning off the power Blinking in orangeSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundAdjusting the zoom and focus Searching an input signalSelecting an input signal Selecting an aspect ratioAdjusting the position Using the automatic adjustment feature For a video signal or s-video signal  For a component video signalCorrecting the keystone distortions Using the magnify featureTemporarily blanking the screen Freezing the screenOperating the computer screen Available function Remote control operationUSB mouse and keyboard control Move pointerUsing the menu function Multifunctional settingsEasy Menu Advanced MenuEasy Menu Easy Menu Using the buttons / adjusts the contrast. Strong  Weak Using the buttons / adjusts the brightness. Light  DarkUsing the buttons / switches the Gamma mode Picture MenuColor Temp Picture MenuLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1 MY MemoryImage Menu PhaseOver Scan PositionImage Menu Auto AdjustSize ExecuteProgressive Input MenuVideo NR Color SpaceComponent Input MenuVideo Format Frame LockCustom Resolution BOX ResolutionNormal  Whisper Setup MenuUsing the buttons / switches the mode for mirror status Setup MenuVolume AudioBlank Screen MenuScreen Menu Start UPMyScreen Lock No Input is Detected Sync is OUT of Range MessageSource Name Auto Search Option MenuStone Auto onOption Menu Reset  CancelAuto OFF Lamp TimeFAN Speed ServiceGhost Filter MessageRemote Freq Factory Reset1NORMAL  2HIGH InformationInputting the Password Using Security FeaturesChanging the Password SecurityDescription If you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Setting the PasswordUsing the PIN Lock Function Turning the Password offRegistering the PIN Code If you have forgotten your PIN Code Turning Off the PIN Lock FunctionUsing the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Setting the Transition Detector off Lamp MaintenanceLamp Case of replacement by yourselfType number = RLC-017 Lamp cover Screw ScrewsHandle Filter cover Air filterAir filter’s knob Air filterPJ658 There is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Power switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workAudio setting is not correct Volume is adjusted to an extremely low levelColor settings are not correctly adjusted Color Space setting is not suitableEither the focus and/or horizontal phase settings are Not properly adjustedWhisper function is working Lamp is approaching the end of its product life TimeSpecifications Warranty and after-serviceSpecifications Country Web Site =Telephone Mail Region =Fax Customer SupportWhat the warranty covers Limited Warranty ViewSonic Projector

PJ658 specifications

The ViewSonic PJ658 is a versatile and powerful portable projector, designed to meet the needs of both business professionals and educators. Combining advanced technologies with user-friendly features, this projector stands out in the crowded market of portable projection solutions.

One of the main features of the PJ658 is its impressive brightness level. With a high lumen output, the projector delivers vivid and clear images even in well-lit environments. This makes it an ideal choice for conference rooms or classrooms where ambient light can be a challenge. The ability to project bright, detailed images ensures that presentations are engaging and easily viewable by all attendees.

The PJ658 utilizes DLP technology, which is known for its reliability and high-quality image production. DLP projectors are recognized for their sharpness, color accuracy, and ability to produce high contrast ratios, allowing for vibrant colors and deep blacks. This technology also contributes to the PJ658's ability to deliver smooth motion graphics, making it an excellent choice for video presentations as well.

Another notable feature of the PJ658 is its versatile connectivity options. Equipped with HDMI, VGA, and USB ports, this projector enables seamless connections to a variety of devices, including laptops, tablets, and external media players. This flexibility allows users to easily switch between devices during presentations without any technical hitches.

Portability is a key characteristic of the PJ658. Its compact and lightweight design allows users to easily transport the projector from one location to another. Whether moving from office to office or carrying it to a remote training session, the PJ658 is designed for convenience. Additionally, it features an easy-to-use interface, enabling users to set up and start presentations in no time.

The PJ658 also comes with built-in speakers, which add to its usability in various settings. This feature eliminates the need for external audio equipment, making it even more convenient for mobile users. Whether for a meeting, lecture, or casual viewing, the PJ658 is equipped to handle audio output effectively.

In terms of lamp life, the PJ658 boasts an extended lifespan, reducing the frequency and cost of lamp replacements. This not only enhances the projector's longevity but also provides users with a cost-effective solution in the long run.

Overall, the ViewSonic PJ658 combines robust performance, advanced technologies, and user-friendly design, making it a top choice for anyone in need of a reliable portable projector. Its brightness, image quality, and connectivity options set it apart, making it suitable for various professional and educational applications.