Intel GS-SR168 manual Federal Communications Commission FCC Statement

Page 5

Safety Information

*To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord.

*Do not plug a modem or telephone cable into the network interface controller (NIC) receptacle.

*Disconnect the modem cable before opening a product enclosure, touching or installing internal components, or touching an uninsulated modem cable or jack.

*Do not use a telephone line to report a gas leak while you are in the vicinity of the leak.

Federal Communications Commission (FCC) Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Neither the provider nor the manufacturer are responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

FCC part 68 (applicable to products fitted with USA modems)

The modem complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company.

If your telephone equipment causes harm to the telephone network, the Telephone Company may discontinue your service temporarily. If possible, they will notify in advance. But, if advance notice is not practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with the FCC.

5

Image 5
Contents System Installation Guide Table of Content Security Server Precaution for Product with Laser Devices Safety, Care and Regulatory InformationImportant safety information FCC part 68 applicable to products fitted with USA modems Federal Communications Commission FCC StatementCanadian Department of Communications Compliance Statement Page Introduction Contents PackagesProcessor Supported Features SummarySuper I/O System Overview Step System Hardware InstallationChassis Removal and Installation Pin1 indicator CPU InstallationMemory Installation Heat Sink InstallationPCI Expansion Card Installation Hard Disk Drive Installation FAN Duct Removal and Installation Front View of GS-SR168 Appearance of GS-SR168Rear View of GS-SR168 Hg f e Back Plane Borad Layout IntroductionNMI Switch and LED Indicators IntroductionName Color Condition Description LAN LED DescriptionConnector Icon Description GA-9IVDPL Motherboard Layout Motherboard Layout & Jumper SettingClrcmos Clear Cmos Function Jumper SettingControlkeys Bios SetupBoot Status Page Setup Menu / Option Page Setup MenuMainMenu MainSystem Date System TimeBit I/O SystemInformation About This Section Advanced AdvancedOnboard VGA Control PCI ConfigurationOnboard LAN Control Option ROM ScanLegacy USB Support Advanced Chipset ControlUSB Controller PCI-E portA Device Force Compliance Mode4GB PCI HoleGranularity Wake On LANSet Max Ext Cpuid = Advanced Processor OptionHyper Threading Technology Serial Port a Peripheral ConfigurationFloppy disk controller Serial Port BFloppy Check Parallel ATANativeModeOperation SATARAIDEnableSerial ATA Extended MemoryTesting Reset ConfigurationDataClk Gen Spread Spectrum System After AC BackHardware Monitor CPU 1&2/Backboard 1/2/3 TemperatureAbout This Section Security Set Supervisor PasswordPassword on boot Set User PasswordConsole Redirection ServerBaud Rate Com PortAddressConsole Type FlowControlHaltOn Memory RAS Feature ControlClear Mem. ECC Error Info Boot Device Priority About This Section BootAbout This Section Exit ExitExit Discarding Changes Load SettupDefaultExit Saving Changes Save Changes Discard ChangesAcronyms AppendixIoapic