ViewSonic PJ1172 manual Network Setting Up, When you use a Network unsuitable to the Dhcp function

Page 39

Network Setting Up

This projector provides the NETWORK function. If you use this function, please consult your dealer for information.

To start, connect the NETWORK port to a gateway device via a RJ-45 (10BASE-1) cable, then set up the projector according to the Network environment in which you use it.

When you use a Network unsuitable to the DHCP function

Please set the IP Address, the Subnet Mask, the Gateway and the DHCP (on/off) using the NETWORK menu, referring to the section “NETWORK Menu”.

When you use a Network suitable to the DHCP function or has been set up

You can set the IP Address, the Subnet Mask, the Gateway and the DHCP (on/off) using a Web Browser of the computer connected to the Network. Although it needs a Web Browser of Internet Explorer 4.0 or higher.

Input the same IP address as set to the projector, to the Web Browser of the computer connected to LAN.

ex. Case of IP Address = 192.168.1.11

1)Input “http://192.168.1.11”.

2)Click “ENTER”.

3)Input the required data according to the screen.

4)Make sure of the input data, then click "Write".

memo These setting will be active after reboot. These setting will be stored, and used when DHCP is OFF.

5)Click “Return to top page”.

6)Click “REBOOT” to complete this operation.

ViewSonic PJ1172

34

Image 39

Contents ViewSonic CE Conformity Compliance InformationImportant Safety Instructions For Your Records Electronic Warranty RegistrationContents Preparation Projector FeaturesPart Names ProjectorProjector Front/Right Projector Rear/Left Control Buttons Remote ControlLaser Indicator Remote ControlSide View Reference for the 43 aspect ratio Setting UpArrangement Side ViewAdjusting The Projector’s Elevator Plug-and-Play Capability Connecting Your DevicesExamples of connection with a computer Scart Examples of connection with a VCR/DVD PlayerConnecting The Power Supply Remote Control Installing BatteriesAbout The Laser Pointer Using The Remote ID Feature Operating The Remote ControlUsing The Mouse/Keyboard Control Function Power On/Off Turning On The PowerTurning Off The Power Operating Selecting An Input SignalAt a RGB signal Using The Automatic Adjustment FeatureAt a M1-D signal At a RGB signal not M1-D At a video signalCorrecting The Keystone Distortion Adjusting The Picture PositionAdjusting The Volume Muting The SoundTemporarily Blanking The Screen Freezing The Screen Using The Magnify FeatureSelecting An Audio Input Displaying The Child WindowMultifunctional Settings Using The Menu FunctionsEx. Turning off the built-in speaker Main Menu Custom Menu PICTURE-1 MenuMY Memory PICTURE-2 Menu Input Menu P. Posit PowerupP. Input Video  S-VIDEOAuto Menu AdjustPower OFF Power onRGB BNC Video  S-VIDEO  Component SearchMenu Position Screen MenuBlank Start UPMessage How to register your picture as the MyScreenOption Menu Service Menu Setup Network MenuDhcp Network Setting Up When you use a Network unsuitable to the Dhcp functionEx. Case of IP Address = About disposal of a lamp LampReplacing The Lamp Case of replacement by yourselfCaring For The Air Filter Air FilterCaring For The Lens Caring For The Cabinet And Remote ControlOther Care Caring For The Inside Of The ProjectorRelated Messages TroubleshootingRegarding The Indicator Lamps Cooling fan is not operating It is time to clean the air filter, or there is no airEither there is no lamp and/or lamp cover, or Either of these has not been properly fixedPhenomena That May Easily Be Mistaken For Machine Defects Tion such as by a power outage blackout, etcVolume is adjusted to an extremely low level This specifications are subject to change without notice SpecificationsCountry/Region Web site = Telephone Customer SupportWhat the warranty does not cover What the warranty coversHow long the warranty is effective Who the warranty protectsPage Sales outside the U.S.A. and Canada Limitation of implied warrantiesExclusion of damages Effect of state law