Eiki EIP-1600T Rest your eyes occasionally, Perature, Do not block the exhaust and intake vents

Page 12
■ After the projector is purchased, a faint smell from the vent may appear when the power is first turned on. This is normal and is not a malfunction. It will disappear after the projec- tor is used for a while.
■ Place the projector on a level site within the adjustment range (8 degrees) of the adjust- ment foot.
tor

Observe the following safeguards when setting up your projector.

Caution concerning the lamp unit

■Potential hazard of glass par-

ticles if lamp ruptures. In case of lamp rupture, contact your nearest EIKI Authorized Dealer or Service Center for replacement.

See “Replacing the Lamp” on page 54.

Caution concerning the setup of the pro- jector

■For minimal servicing and to maintain high image quality, EIKI recommends that this pro- jector be installed in an area free from hu- midity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more of- ten. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by an EIKI Authorized Dealer or Service Cen- ter.

When using the projector in high-altitude areas such as mountains (at altitudes of approximately 4,900 feet (1,500 meters) or more)

■When you use the projector in high-altitude areas with thin air, set “Fan Mode” to “High”. Neglecting this can affect the longevity of the optical system.

Warning about placing the projector in a high position

■When placing the projector in a high position, ensure that it is secured carefully to avoid per- sonal injury caused by the projector falling down.

Do not subject the projector to hard im- pact and/or vibration.

■Protect the lens so as not to hit or damage the surface of the lens.

Rest your eyes occasionally.

■Continuously watching the screen for long hours will cause eye strain. Be sure to occa- sionally rest your eyes.

Do not set up the projector in places ex- Avoid locations with extremes of tem-

posed to direct sunlight or bright light.

■Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.

perature.

■The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C).

■The storage temperature of the projector is from –4°F to 140°F (–20°C to +60°C).

Do not block the exhaust and intake vents.

Caution regarding placing of the projec- ■ Allow at least 11 13/16 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction.

■ Be sure that the intake vent and the exhaust vent are not obstructed.

■ If the cooling fan becomes obstructed, a pro- tection circuit will automatically put the pro- jector into standby mode to prevent overheat

damage. This does not indicate a malfunc-

tion. (See pages 52 and 53.) Remove the pro- jector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.

8

EIP-1600T_EN_b

8

06.1.24, 1:01 PM

Page 11 Page 13
Image 12
Page 11 Page 13
Contents EIP-1600T EIP-1600TENa 06.1.16, 906 AM Model No. EIP-1600T Serial No EIP-1600TENa 06.1.24, 100 PM Introduction Information Esperanza Rancho Santa Margarita, CA 92688-2132 TELUsing the Menu Screen For Future ReferenceContents Maintenance Maintenance Indicators Regarding the Lamp ReferenceCleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingRest your eyes occasionally PeratureDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Accessories Optional accessoryPower Indicator Focus ring For adjusting the focusPart Names and Functions ProjectorPart Names and Functions Rear ViewUsing the Kensington Lock on the projector Inserting the Batteries Attach the cover and slide it until it clicks into placeUsable Range Setup and Projection Quick StartAdjust the focus, image size, and projector angle PP Setting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupProjection PRJ Mode 174⋅98Setting up the Projector When using a wide screen 169 and projecting 169 imagePicture Screen Size and Projection Distance When using a normal screen 43 and projecting 169 image Samples of Cables for Connection Connecting to Video Equipment Connecting to Video Equipment Video cableWhen connecting to equipment with Hdmi output teminal INPUT6 Connecting to a Computer Computer To RGB output terminalTo INPUT5 terminal RGB cable commercially available Controlling the Projector by a Computer To RS-232C terminalConnecting the Power Cord Lamp indicator Power indicator STANDBY-ON button On buttonTurning the Projector On/Off Turning the Projector onSwitching the Input Mode Unplug the power cord from the ACImage Projection Outlet after the cooling fan stopsAdjusting the Projected Image Adjust lever Make small adjustmentsImage Projection Rotate the zoom ring to enlarge or shrink the screen sizeUse the rear adjustment foot to make the projector level Correcting Trapezoidal Distortion Display disappears For correcting an image byDesignating the corner Projected imageRepeat the same procedure with Press i Enter to set the posi- tionPositions for the upper right Lower right and lower left ImageKeystone Resize Mode On the projector On the remote control Resize buttonAbout Copyrights ComputerOperating with the Remote Control Switching the Iris SettingSelecting the Picture Mode Shifting the Projected Im- age Vertically Image ShiftMenu Items Picture menuMenu Items Fine Sync menuUsing the Menu Screen Menu Selections AdjustmentsIcon to adjust Press dMENUUsing the Menu Screen To adjust the projected image while watching itPress P or R to select the item to adjust Press O or Q to adjust the item selectedPicture Adjustment Picture menu 1Selecting the Picture Mode2Adjusting the Image Menu operation nPicture Adjustment Picture menu 3Adjusting the Color Temperature4Adjusting the Colors Progressive6Reducing Image Noise 7Switching the Iris Setting8Lamp Setting 1Adjusting Computer Image 2Special Modes Setting3Auto Sync Auto Sync Adjustment 4Checking the Input SignalUsing the Options Menu 1Adjusting the Image Position2Adjusting the Overscan ButtonUsing the Options Menu 9Auto Power Off Function 0Checking the Lamp Life StatusReversing/Inverting Projected Images 4Fan Mode Setting 5Returning to the Default Settings2Selectingthe Transmission Speed RS-232C 6Selecting the On-screen Display LanguageMaintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorOff Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer Regarding the LampConnecting Pin Assignments GNDRS-232C Specifications and Command Settings Connecting Pin AssignmentsReturn code 0DH R Return code 0DHComputer Compatibility Chart Vesa HdmiTroubleshooting 23-27Black levels Specifications Product type Projector Model EIP-1600T Video systemDimensions Index Canada Eastern EuropeDeutschland & Österreich Japan & Worldwide

EIP-1600T specifications

The Eiki EIP-1600T is an advanced, high-performance projector designed to meet the needs of educational institutions, corporate environments, and large venues. This model stands out for its exceptional image quality, versatile connectivity options, and user-friendly features, making it a popular choice for various presentation settings.

One of the main features of the EIP-1600T is its impressive brightness level, boasting up to 6,000 ANSI lumens. This level of brightness enables clear and vivid projections even in well-lit rooms, ensuring that presentations remain visible without the need to dim ambient light. The projector also offers a full HD resolution of 1920 x 1080 pixels, which allows for sharp images and detailed visuals that enhance the viewing experience.

In terms of technology, the Eiki EIP-1600T utilizes DLP (Digital Light Processing) technology, which is renowned for its reliability and superior color accuracy. This feature ensures that colors are vibrant and lifelike, making it ideal for displaying multimedia content, including videos, images, and presentations. Additionally, the DLP chip used in this projector guarantees a longer lifespan compared to other projection technologies, delivering longevity and consistent performance.

Connectivity is another strong point of the EIP-1600T. The projector is equipped with multiple input options, including HDMI, VGA, composite video, and USB ports. These versatile connectivity options make it compatible with a wide range of devices, from laptops to media players, allowing presenters to switch between sources seamlessly. Furthermore, the projector supports wireless connectivity through optional adapters, enabling users to project content from smartphones, tablets, or laptops without the hassle of tangled cables.

The EIP-1600T also incorporates user-friendly features such as a built-in speaker and a comprehensive remote control. The onboard speaker produces adequate sound for small to medium-sized rooms, enhancing the overall presentation experience. The intuitive remote makes navigating menus and adjusting settings easy, thus simplifying the setup process.

In conclusion, the Eiki EIP-1600T is a powerful projector that combines high brightness, excellent resolution, and versatile connectivity, making it suitable for a variety of applications. Its robust construction and user-friendly features further contribute to its appeal, ensuring reliable performance in any professional setting. Companies and educational institutions looking for a dependable, high-quality projection solution will find the EIP-1600T to be a valuable asset.
Top Page Image Contents