Eiki EIP-1600T owner manual Off

Page 57

Maintenance indicator

Problem

 

Cause

 

Possible Solution

 

 

 

 

 

 

Normal

Abnormal

 

 

 

 

 

 

 

 

 

 

 

 

Tempera-

Off

Red on

The internal

Blocked air intake

• Relocate the projector to

ture

 

(Standby)

temperature is

 

 

 

an area with proper

warning

 

 

abnormally

 

 

 

ventilation. (see page 8)

indicator

 

 

high.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cooling fan

• Take the projector to your

 

 

 

 

 

breakdown

 

nearest EIKI Authorized

 

 

 

 

Internal circuit

 

Dealer or Service Center

 

 

 

 

 

failure

 

for repair.

 

 

 

 

Clogged air intake

 

 

 

 

 

 

 

 

 

Lamp

Green on

Red on

The lamp does

The lamp is shut

• Disconnect the power cord

indicator

(Green

 

not illuminate.

 

down abnormally.

 

from the AC outlet, and

 

blinks

 

 

 

 

 

then connect it again.

 

when the

 

 

 

 

 

 

 

 

Time to change

Remaining lamp life

• Carefully replace the lamp.

 

lamp is

 

 

 

the lamp.

 

becomes 5% or

 

(See page 55.)

 

warming

 

 

 

 

 

 

 

less.

Take the projector to your

 

up or

 

 

 

 

 

 

 

 

 

nearest EIKI Authorized

 

Red on

The lamp does

Burnt-out lamp

 

 

turning

 

 

 

Dealer or Service Center

 

(Standby)

not illuminate.

Lamp circuit failure

 

 

off.)

 

for repair.

 

 

 

 

 

 

 

 

 

 

 

 

• Please exercise care when

 

 

 

 

 

 

 

replacing the lamp.

 

 

 

 

 

 

Securely install the cover.

Power

Green on/

Green

The power

The lamp unit cover

• If the power indicator blinks

indicator

Red on

blinks

indicator blinks

 

is open.

 

in green even when the

 

Red

 

in green when

 

 

 

lamp unit cover is securely

 

 

the projector is

 

 

 

installed, contact your

 

blinks

 

 

 

 

 

 

on.

 

 

 

nearest EIKI Authorized

 

(Cooling)

 

 

 

 

 

 

 

 

 

 

Dealer or Service Center

 

 

 

 

 

 

 

 

 

 

 

 

 

 

for advice.

 

 

 

 

 

 

 

 

Info

If the temperature warning indicator illuminates, and the projector enters standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plug- ging in the power cord and turning the power back on. (At least 10 minutes.)

If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illumi- nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.

The cooling fan keeps the internal temperature of the projector constant and this function is con- trolled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.

Do not unplug the power cord after the projector has entered standby mode and while the cooling fan is running. The cooling fan runs for about 90 seconds.

53

EIP-1600T_EN_l

53

06.1.24, 1:08 PM

Image 57
Contents EIP-1600T EIP-1600TENa 06.1.16, 906 AM Model No. EIP-1600T Serial No EIP-1600TENa 06.1.24, 100 PM Introduction Esperanza Rancho Santa Margarita, CA 92688-2132 TEL InformationFor Future Reference Using the Menu ScreenContents Reference Maintenance Maintenance Indicators Regarding the LampAccessories CleaningPower Sources Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingRest your eyes occasionally PeratureDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Optional accessory AccessoriesFocus ring For adjusting the focus Power IndicatorPart Names and Functions ProjectorRear View Part Names and FunctionsUsing the Kensington Lock on the projector Attach the cover and slide it until it clicks into place Inserting the BatteriesUsable Range Quick Start Setup and ProjectionAdjust the focus, image size, and projector angle PP Setting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount Setup174⋅98 Projection PRJ ModeSetting up the Projector When using a wide screen 169 and projecting 169 imagePicture Screen Size and Projection Distance When using a normal screen 43 and projecting 169 image Samples of Cables for Connection Connecting to Video Equipment Video cable Connecting to Video EquipmentWhen connecting to equipment with Hdmi output teminal INPUT6 Connecting to a Computer Computer To RGB output terminalTo INPUT5 terminal RGB cable commercially available To RS-232C terminal Controlling the Projector by a ComputerLamp indicator Power indicator STANDBY-ON button On button Connecting the Power CordTurning the Projector On/Off Turning the Projector onUnplug the power cord from the AC Switching the Input ModeImage Projection Outlet after the cooling fan stopsAdjust lever Make small adjustments Adjusting the Projected ImageImage Projection Rotate the zoom ring to enlarge or shrink the screen sizeUse the rear adjustment foot to make the projector level Correcting Trapezoidal Distortion For correcting an image by Display disappearsDesignating the corner Projected imagePress i Enter to set the posi- tion Repeat the same procedure withPositions for the upper right Lower right and lower left ImageKeystone On the projector On the remote control Resize button Resize ModeComputer About CopyrightsSwitching the Iris Setting Operating with the Remote ControlSelecting the Picture Mode Shifting the Projected Im- age Vertically Image ShiftPicture menu Menu ItemsFine Sync menu Menu ItemsMenu Selections Adjustments Using the Menu ScreenIcon to adjust Press dMENUTo adjust the projected image while watching it Using the Menu ScreenPress P or R to select the item to adjust Press O or Q to adjust the item selected1Selecting the Picture Mode Picture Adjustment Picture menu2Adjusting the Image Menu operation n3Adjusting the Color Temperature Picture Adjustment Picture menu4Adjusting the Colors Progressive6Reducing Image Noise 7Switching the Iris Setting8Lamp Setting 2Special Modes Setting 1Adjusting Computer Image3Auto Sync Auto Sync Adjustment 4Checking the Input Signal1Adjusting the Image Position Using the Options Menu2Adjusting the Overscan ButtonUsing the Options Menu 9Auto Power Off Function 0Checking the Lamp Life StatusReversing/Inverting Projected Images 5Returning to the Default Settings 4Fan Mode Setting2Selectingthe Transmission Speed RS-232C 6Selecting the On-screen Display LanguageCleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsOff Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Regarding the Lamp Resetting the Lamp TimerGND Connecting Pin AssignmentsConnecting Pin Assignments RS-232C Specifications and Command SettingsReturn code 0DH R Return code 0DHVesa Hdmi Computer Compatibility Chart23-27 TroubleshootingBlack levels Product type Projector Model EIP-1600T Video system SpecificationsDimensions Index Eastern Europe CanadaDeutschland & Österreich Japan & Worldwide

EIP-1600T specifications

The Eiki EIP-1600T is an advanced, high-performance projector designed to meet the needs of educational institutions, corporate environments, and large venues. This model stands out for its exceptional image quality, versatile connectivity options, and user-friendly features, making it a popular choice for various presentation settings.

One of the main features of the EIP-1600T is its impressive brightness level, boasting up to 6,000 ANSI lumens. This level of brightness enables clear and vivid projections even in well-lit rooms, ensuring that presentations remain visible without the need to dim ambient light. The projector also offers a full HD resolution of 1920 x 1080 pixels, which allows for sharp images and detailed visuals that enhance the viewing experience.

In terms of technology, the Eiki EIP-1600T utilizes DLP (Digital Light Processing) technology, which is renowned for its reliability and superior color accuracy. This feature ensures that colors are vibrant and lifelike, making it ideal for displaying multimedia content, including videos, images, and presentations. Additionally, the DLP chip used in this projector guarantees a longer lifespan compared to other projection technologies, delivering longevity and consistent performance.

Connectivity is another strong point of the EIP-1600T. The projector is equipped with multiple input options, including HDMI, VGA, composite video, and USB ports. These versatile connectivity options make it compatible with a wide range of devices, from laptops to media players, allowing presenters to switch between sources seamlessly. Furthermore, the projector supports wireless connectivity through optional adapters, enabling users to project content from smartphones, tablets, or laptops without the hassle of tangled cables.

The EIP-1600T also incorporates user-friendly features such as a built-in speaker and a comprehensive remote control. The onboard speaker produces adequate sound for small to medium-sized rooms, enhancing the overall presentation experience. The intuitive remote makes navigating menus and adjusting settings easy, thus simplifying the setup process.

In conclusion, the Eiki EIP-1600T is a powerful projector that combines high brightness, excellent resolution, and versatile connectivity, making it suitable for a variety of applications. Its robust construction and user-friendly features further contribute to its appeal, ensuring reliable performance in any professional setting. Companies and educational institutions looking for a dependable, high-quality projection solution will find the EIP-1600T to be a valuable asset.