Eiki LC-SD15 owner manual Compliance, Federal Communication Commission Notice

Page 7

Compliance

Federal Communication Commission Notice

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Number

: LC-SD15

Trade Name

: EIKI

Responsible party

: EIKI International, Inc.

Address

: 30251 Esperanza, Rancho Santa Margarita,

 

CA 92688-2132 U.S.A.

Telephone No.

: 800-242-3454 (949-457-0200)

AC Power Cord Requirement

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into the

outlet, contact your electrician.

GROUND

 

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

7

Image 7
Contents Model LC-SD15 Features and Design Table of Contents Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsAir Circulation Installing the Projector in Proper PositionMoving the Projector Federal Communication Commission Notice ComplianceBottom Part Names and FunctionsFront BackFunctions Rear TerminalTop Control Part Names and Functions Remote Control Operating RangeTwo AA size batteries Remote Control Battery InstallationAdjustable Feet InstallationPositioning the Projector For the U.S.A. and Canada For Continental Europe Connecting the AC Power Cord200 240 V AC Installation Connecting to a ComputerCables used for connection Service Port Connecting to Video EquipmentBasic Operation What is PIN code?Basic Operation Turning On the ProjectorTurning Off the Projector Zoom and Focus Adjustment Top Control How to Operate the On-Screen MenuRemote Control On-Screen MenuMenu Bar No Show Function Dim ModeKeystone Correction Picture Freeze FunctionMenu Operation Timer FunctionSound Adjustment Direct OperationComputer Video Computer InputInput Source Selection Input MenuComputer Input Computer System SelectionSelecting Computer System Manually Auto PC adj Auto PC AdjustmentPC Adjust Menu To store the adjusted parametersManual PC Adjustment Display area H ResetMode free Display areaImage Level Selection Image Level Adjustment Screen Size Adjustment RGB Scart Video InputVideo ComponentAuto Video System SelectionVideo Input Video or S-VideoImage button Dynamic Standard Cinema BlackboardGreen CinemaImage1~4 Tint ColorSharpness Film ProgressiveProvides image at the normal video aspect ratio of 4 Setting SettingTo Change the Logo PIN code SettingLogo PIN code lock Enter a Logo PIN codeRear LogoCapture CeilingPower management Power managementLamp mode Dim modeKey lock To change the code of the remote controlRemote control To change the code of the projectorPIN code lock To Change the PIN code lock settingTo Change the PIN code Fan Lamp counter resetFactory default Fan Factory defaultProjector is shut down and the Warning indicator lights red Maintenance and CleaningMaintenance CleaningRecommendation Cleaning the Air FiltersAttaching the Lens Cover Cleaning the Projection LensCleaning the Projector Cabinet Maintenance & CleaningOrder Replacement Lamp Lamp ReplacementLamp Replacement Counter Lamp Handling PrecautionsAppendix TroubleshootingAppendix Remote Control does not workSome displays are not seen during the operation Menu Tree Image Adjust Screen AutoSettingSystem Image Select Projector Condition Indicators and Projector ConditionFreq Compatible Computer SpecificationsKHz Technical Specifications Optional Parts AccessoriesTerminal Mini D-sub 15 pin Configurations of TerminalsTerminal Mini DIN 8-PIN PIN Code Lock No PIN Code Number MemoLogo PIN Code Lock No Key to better communications Canada