Intel MS-6734, KM4M, KM4AM, G52-M6734XD manual FCC-B Radio Frequency Interference Statement

Page 2

Manual Rev: 1.5

Release Date: July 2004

FCC-B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Opera- tion of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

Notice 1

The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limits.

VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AU RESEAU.

Micro-Star International

MS-6734

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation

ii

Image 2
Contents KM4M/KM4AM Series Voir LA Notice D’INSTALLATION Avant DE Raccorder AU Reseau FCC-B Radio Frequency Interference StatementRevision History Copyright NoticeTrademarks Revision Revision History DateSafety Instructions Technical SupportContents Bios Setup Getting Started Mainboard Specifications CPUBios LANMainboard Layout MS-6734 v1.X M-ATX MainboardHardware Setup Quick Components Guide SATA1, SATA2Then CPU Core Speed Derivation ProcedureCentral Processing Unit CPU CPU Installation Procedures for Socket Unplug the power cord before Installing the CPUInstalling AMD Athlon CPU Socket 462 Cooler Set MSI Reminds YouCPU Clock Frequency Selection through Bios OverheatingDDR Dimm Slots DIMM1 MemoryMemory Speed/CPU FSB Support Matrix Installing DDR Modules Dimm Module CombinationATX 12V Power Connector JPW1 Power SupplyATX 20-Pin Power Connector CONN1 CONN1MIC Mouse ConnectorBack Panel USB COM VGAPS/2 Keyboard 6-pin Female Keyboard ConnectorUSB Connectors USB PortsPin Male DIN Connector Serial Port Connector COMVGA Connector IEEE1394 Port OptionalRJ-45 LAN Jack Optional Audio Port ConnectorsLine Stereo Audio Connectors Line Out Mic LAN JackParallel Port Connector LPT1 Fan Power Connectors CPUFA1/SYSFA1 ConnectorsFloppy Disk Drive Connector FDD1 FDD1Hard Disk Connectors IDE1 & IDE2 IDE1 IDE2Optional Serial ATA cable JFP2 Front Panel Connectors JFP1 & JFP2CD-In Connector JCD1 JFP1JUSB3 Optional Front USB Connectors JUSB2 & JUSB3 JUSB3 is optionalJUSB2 USB 2.0 BracketIEEE1394 Bracket Optional Ieee 1394 Connectors J13941 & J13942 OptionalJ13941 / J13942 Optional JAUD1 Front Panel Audio Connector JAUD1SPDIF-Out Connector JSP1 JSP1CPU Frequency Jumpers SW1 & SW2 JumpersClear Cmos Jumper JBAT1 JBAT1PCI Peripheral Component Interconnect Slots SlotsAGP Accelerated Graphics Port Slot PCI Interrupt Request RoutingBios Setup Getting Help Entering SetupControl Keys Main Menu Set Supervisor Password Load Fail-Safe DefaultsLoad Optimized Defaults Set User PasswordMonth Standard Cmos FeaturesDay YearBase/Extended/Total Memory VideoHalt On Advanced Bios Features Typematic Delay Msec Boot Up NumLock StatusTypematic Rate Setting CPU Internal CacheHDD S.M.A.R.T. Capability Apic ModeMPS Table Version Current FSB / Dram / DDR Frequency Advanced Chipset FeaturesDram Clock/Drive Control Dram ClockBank Interleave Dram Command RateDram CAS Latency Precharge To Active TrpAGP Aperture Size AGP ModeAGP & P2P Bridge Control AGP Driving ControlIntegrated Peripherals Primary/Secondary Master/Slave UltraDMA Onboard Lan Boot ROMPrimary/Secondary Master/Slave PIO VIA OnChip PCI DeviceSPP/EPP/ECP/ECP+EPP ECP Mode Use DMA Init Display FirstIpca Function Power Management SetupPower Management Option Sleep StatePower Button Function HDD Power DownSuspend Mode Run Vgabios if S3 ResumePS2KB Wake Up from S3/S4/S5 Resume By AlarmPS2KB Wakeup Select PS2MS Wake Up from S3/S4/S5IRQ Activity Monitoring Dateof Month AlarmTimehhmmss Alarm Primary IntrResource Controlled By PNP/PCI ConfigurationsClear Escd IRQ ResourcesPCI/VGA Palette Snoop Assign IRQ for VGA/USBPC Health Status CPU Warning TemperatureShutdown Temperature Spread Spectrum Frequency/Voltage ControlAuto Detect DIMM/PCI Clk Load Fail-Safe/Optimized Defaults Set Supervisor/User Password About Supervisor Password & User PasswordAudio Function RAID 0 Striping IntroductionRAID Basics RAID 1 MirroringBios Configuration Create Disk Array VIA VT8237 Serial ATA RAID Introduction Delete Disk Array Create and Delete Spare Hard Drive View Serial Number of Hard DriveDuplicate Critical RAID 1 Array Rebuild Broken RAID 1 ArrayContinue to boot Power off and Check the Failed DriveChoose Replacement Drive and Rebuild Destroy the Mirroring RelationshipNew Windows OS 2000/XP/NT4 Installation Installing RAID Software & DriversInstall Driver in Windows OS Existing Windows XP Driver InstallationInstallation of VIA Sata RAID Utility MS-6734 M-ATX Mainboard Using VIA RAID Tool MS-6734 M-ATX Mainboard VIA VT8237 Serial ATA RAID Introduction