Installing the bobbin | Brother 885-S61 specs

GETTING READY ———————————————————————————————————————————————————

Installing the bobbin

Install the bobbin wound with thread.

CAUTION

●Use a bobbin thread that has been correctly wound, otherwise the needle may break or the thread tension will be incorrect.

●The bobbin was designed specifically for this sewing machine. If bobbins from older models are used, the machine will not operate correctly. Use only the enclosed bobbin or bobbins of the same type (part code: SA156, XA5539-151).

Actual size

11.5mm (7/16 inch)


This model		Older model

Memo

●The order that the bobbin thread should be passed through the shuttle is indicated by marks around the shuttle. Be sure to thread the machine as indicated.

1Press (needle position button) once or twice to raise the needle, and then raise the presser foot lever.

2Turn off the sewing machine.

3Slide the bobbin cover latch to the right.

1 2

4Remove the bobbin cover.

5Hold the bobbin with your right hand and hold the end of the thread with your left.

• Be careful not to drop the bobbin.

6Insert the bobbin with your right hand so that the end of the thread is on the left, and then, after pulling the thread firmly around the tab with your left hand as shown, lightly pull the thread to guide it through the slit.

1

1Tab

CAUTION

●Be sure to install the bobbin so that the thread unwinds in the correct direction, otherwise the thread may break or the thread tension will be incorrect.

1Bobbin cover

2 Latch

XThe bobbin cover opens.

22

Image 28

Brother 885-S61 operation manual Installing the bobbin

Contents

Read before use Enclosed Accessories Accessories Names of Machine Parts and Their Functions Front view Needle and presser foot section Right-side/rear view Operation buttons Start/stop button Operation panel LCD liquid crystal display Optional Accessories Sewing Machine Features Introduction Contents Adjusting the Thread Tension Adjusting the Stitch Width and LengthSewing Useful Functions 127 Important Safety Instructions For a longer service life For Users in the UK, EIRE, Malta Cyprus only Getting Ready Power supply precautions Turning the Machine On/Off Turning off the machine Turning on the machineTurning the Machine On/Off Understanding the LCD Screens Checking machine operating procedures Understanding the LCD Screens Changing the Machine Settings Changing the settings2Presspanel. settings key in the operation 6Press OK key Changing the Machine Settings List of stitch or machine attribute Adjusting the brightness of the LCD Changing the needle stop positionArrow keys until is selected 2Press OK key 3Press To select To return to Changing the screen language Bobbin precautions Winding/Installing the BobbinWinding the bobbin 4Slide the bobbin winder shaft to the right Winding/Installing the BobbinPlace the spool of thread for the bobbin onto the spool pin Pass the thread under the thread guide plate from the right DPress start/stop button once EPress start/stop button once Installing the bobbin Then, pull the thread toward you to cut it with the cutter 8Reattach the bobbin cover Threading the upper thread Upper Threading1Turn on the sewing machine 2Raise the presser foot lever 4Lift open the upper cover Upper ThreadingPlace the spool for the upper thread onto the spool pin Shutter 3Lower the presser foot lever Threading the needle4Lower the needle threader lever until it clicks Using the twin needle 1Threadguide. the machine to the needle bar thread2Lower the presser foot lever Threadeye. the upper thread for the left needle 3Manually thread the left needle with the upper thread 4Insert the extra spool pin onto the bobbin winder shaftAttach zigzag foot J 0Turn on the sewing machine APress settings key in the operation panel Press , , and arrow keys until Is selected Press OK keyPress to select EPress OK key Using thread that winds off quickly Pulling up the bobbin thread Getting Ready Needle precautions Replacing the NeedleNeedle types and their uses Replacing the Needle Correct needle Checking the needleIncorrect needle Replacing the needle Getting Ready Presser foot precautions Replacing the Presser FootReplacing the presser foot Replacing the Presser Foot Presser foot holder releases the presser foot Adjusting the pressure of the presser foot 3When you are finished sewing, reset the dial to 3 standardRemoving the presser foot holder Lower the presser foot lever Using the walking foot Attaching the walking footRemove the presser foot holder 2Turn off the sewing machine For details, refer to Removing the presser foot holder Stitching cylindrical pieces Sewing Cylindrical or Large PiecesSewing large pieces of fabric Sewing Cylindrical or Large Pieces Getting Ready Sewing Basics Sewing General sewing procedure Sewing Positioning the fabric 3Place the fabric under the presser foot Starting to sew Machine stops sewing with the needle lowered in the fabric Securing the stitching Sewing reinforcement stitches Using the manual thread cutter Cutting the thread Adjusting the Thread Tension Changing the tension of the upper threadCorrect thread tension Upper thread is too tight Adjusting the stitch width Adjusting the Stitch Width and Length2Select a stitch Adjusting the stitch length Useful Functions Useful Functions Reverse/reinforcement stitch button Automatically cutting the thread 7Press OK key Press , , and arrow keys until Is selected 4Press OK key Saving stitch settings5Check the is selected, and then press OK key Settings, press so that , and then press OK key Useful Sewing Tips Trial sewingChanging the sewing direction Sewing curves Useful Sewing Tips Sewing thick fabrics4Releasebutton.the presser foot locking pin black Sewing thin fabrics Sewing stretch fabricsSewing leathers or vinyl fabrics Sewing an even seam allowance Useful Sewing Tips Sewing Basics Utility Stitches Stitch types Selecting StitchingSelecting stitching Understanding the screen Selecting Stitching9Press OK key Overcasting Stitches Sewing overcasting stitches using overcasting foot GAttach overcasting foot G Sewing overcasting stitches using zigzag foot J Overcasting Stitches Sewing overcasting stitches using the optional side cutter Remove the presser foot Position the fabric in the side cutter Lower the presser foot lever, and then start Asewing Basting Basic StitchingBasic stitching Basic Stitching When sewing is finished, cut the threadChanging the needle position Blind Hem Stitching Stitch3Attach blind hem foot R 4Select a stitch Blind Hem Stitching If the needle catches too much of the hem fold Buttonhole Stitching Buttonhole sewing Buttonhole Stitching 3Attach buttonhole foot a If the button does not fit in the button guide platePullpossible.down the buttonhole lever as far as Sewing buttonholes on stretch fabrics 2Attach buttonhole foot a Button sewingAttach button-sewing foot M 4Select stitch 3Place the button into button-sewing foot M6Start sewing Attaching a shank to a button 3Cut off any excess thread Inserting a centered zipper Zipper InsertionZipper Insertion Inserting a side zipper 7Select stitch Wrong side of fabric Mm 1/8 inch BTopstitch around the zipper Zipper/piping Insertion Zipper/piping InsertionRefer to -4of Inserting a centered zipper Inserting a piping 8Topstitch around the zipper Sewing Stretch Fabrics and Elastic Tape Stretch stitchingElastic attaching Sewing Stretch Fabrics and Elastic Tape 3Select a stitch Appliqué, Patchwork and Quilt Stitching Appliqué stitchingAppliqué, Patchwork and Quilt Stitching Quilting 4Attach the optional open toe foot Patchwork crazy quilt stitching Piecing3Select stitch 57 or For a seam allowance on the left side Quilting Using the optional quilting guideBaste the fabric to be quilted Attach the walking foot Free-motion quilting Turnstitch.on the sewing machine, and then select a Satin stitching Connect the foot controller 8Select stitch Reinforcement Stitching Triple stretch stitchingBar tack stitching 2Select stitch 3Select stitch Reinforcement Stitching5Pullpossible.down the buttonhole lever as far as Darning 3Select stitch 52 or Memo Eyelet Stitching Attach monogramming foot N Decorative Stitching Eyelet Stitching/Decorative Stitching Fagoting 3Attach zigzag foot J4Select stitch 26 or Set the stitch width to 7.0 mm 1/4 inch Smocking Scallop stitchingDecorative Stitching Shell tuck stitching Select stitch 25 , 26 orFold the fabric along the bias 2Attach zigzag foot J Select stitch 20 , and then increase the thread tension Unfold the fabric, and then iron the tucks down to one side Joining3Select stitch 22 , 23 or 1Install the wing needle Heirloom stitching2Attach monogramming foot N 4Start sewing 6Press , , and arrow keys until is selected 7Press OK key ASet .the mirror image pattern setting back to8Press To select To return to , press 4Sew along the center of the unfrayed section Sewing the Various Built-In Decorative Patterns Sewing beautiful patternsSewing patterns Sewing the Various Built-In Decorative Patterns Combining patterns 4Sew reinforcement stitches1SelectOK keythe. first pattern, and then press 2Press the + key in the operation panel Repeat sewing patterns Press settings key in the operation panelSelect the pattern Checking the selected pattern 1Press settings key in the operation panelPress , , and arrow keys until Is selected 3Press OK key Changing the pattern size 2Press settings key in the operation panelPressselected. and until the desired size is Changing the stitch density Changing the pattern length5Pressselected. and until the desired density is Pressselected. and until the desired ratio is Mirror imaging the pattern Select a stitch Press settings key in the operation panelPress To select 5To return to 7Checkkey. the contents, and then press OK Storing a pattern2Press stitch selection key Operation panel 3Press , , and arrow keys until is selected 4Press OK key Realigning the pattern 6Checkkey. the contents, and then press OKPress , , and arrow keys until Is selected, and then select Press , , and arrow keys until Is selected 8Press OK key Check the sewn patternPress or + Designing a Pattern Drawing a sketch of the patternDesigning a Pattern 1Drawset. a sketch of the pattern on the grid sheet 8Select , and then press OK key Entering the pattern data9Repeatpoint. steps 6 through 8 to specify each Embroidery screen appears Design exampled Point Appendix Stitch Settings Utility stitches Stitch Settings Stitch 130 Buttonhole 132 Other stitches Stitch Type Pattern PresserFoot NeedleTwin PatternSize 134 Maintenance Cleaning the machine surfaceCleaning the shuttle race Maintenance Surrounding area Align the S and z marks Troubleshooting Troubleshooting 138 Tension is Be used LCD Error messages Error Message Probable Cause Operation beep Nothing appears in the LCD4Turnagain.off the sewing machine, then turn it on Cancelling the operation beep Removing the upper cover5Press To select To return to Hold the upper cover level Index Numerics Index 146 Page Page Page English 885-S61 XF4637-001