Konica Minolta IP-011 manual System Requirements, Case of using Windows 95/98, Parallel Port

Page 10

Introduction

System Requirements

Windows

The following are required to print from the Windows*-compliant computers to the Printer Controller.

Computers on which Windows 95/98, WindowsNT 4.0 can run

CD-ROM drive (necessary to install the user software)

In case of using Windows 95/98

Microsoft Windows 95/98

32MB RAM or more

In case of using Windows NT 4.0

Microsoft Windows NT 4.0 and NT Service Pack 3

32MB RAM or more

Parallel Port

The following are required to print to the Printer Controller by way of the parallel port.

Windows-compliant computers

Minimum RAM capacity suitable for computers (Refer to the section of each operation system described above.)

IEEE 1284 parallel cable

One end of the cable is required to have an amphenol 36 pin male connector (connected to the Printer Controller).

viii IP-011 Printer Controller

Image 10
Contents USER’S Guide Page Make sure to read before use Contents Operation Panel Setup Index Appendix a Troubleshooting Appendix A-1Appendix B Product Specifications Appendix B-1 Appendix B-2About Registered Trademarks IntroductionFCC Regulations CopyrightAbout Supplied Items About Positioning of This Manual About Composition of This ManualSystem Requirements Case of using Windows 95/98Case of using Windows NT WindowsRules in This Manual Outline Outline Contents of This Chapter IP-011 and Printer Engine Copy Mode and Printer ModeOutline of the Printer Controller Conceptual ConnectionOutline IP-011 Hardware ConfigurationInterface Data Flow TCP/IP,IPX/SPX NICHow to Use Memory Memory UpgradingGeneral View About the Status Monitor Outline About the Printer ToolsAbout the Printer Tools About the Control PanelAbout the Printer Driver Compliant OSSetup Setup Contents of This Chapter Files to be Installed Installation of the Printer DriverBefore Installation Models and Environment of ComputersInstallation to Windows95/98 SetupInstallation with the User Software CD Setup Installation by using Add Printer Installation by Using the Plug & PlayInstallation to WindowsNT4.0 Printer Management on WindowsNTInstallation by Using the User Software CD Default C\Program Files\Konica IP-011 Uninstallation of the Printer Driver Test Print Displaying the Setup Screen Setup Print from ApplicationsPrint Settings Execution of PrintingSetup Contents of Settings 14 IP-011 Printer Controller Paper tab 16 IP-011 Printer Controller Watermark tab 18 IP-011 Printer Controller Printer Driver Printer Driver Contents of This Chapter Property of Printer Driver CancelWorking Environment ApplyPrinter Driver Printer Driver Function List COM1, COM2 FileWhether borders are printed or not Chapter Printer Driver Original paper you can set differsAdd Port Alphabetic OrderAbout AlternatePrinter Driver Back cover Capture printer portCopies DefaultDelete port Printer Driver Duplex printing Finisher End CaptureFront Cover Group Front/Back Cover- Paper TrayFront/Back Cover-Paper Type LayoutOption New DriverOption Tray Protection Printer Driver OrientationOutput tray Paper trayPrint page borders Port settingsPaper type Print qualitySet up-Original Paper Printer Driver Print using the following driverSet up-Paper Size Smoothing Settings of the two-way communication functionSharing SortPrinter Driver Spool settings StapleTimeout settings Printer Driver Watermark ZoomChapter Alternate Sorting Layout 24 IP-011 Printer Controller Plain Thick None Trays DB-209 DB-409 Paper Size Control Panel Setup Control Panel Setup Contents of This Chapter About the Control Panel Control Panel of the CopierItem Selection Control Panel SetupHow to Enter Settings on the LCD Panel Information EntryCancel Job Printer Mode Basic ScreenSetting Printer Menu ScreenPrevions Printer Setting screenMain Menu Numeric keysProcedures of the Printer Setting Setting screen of the selected item is DisplayedControl Panel Setup Password Protection Configuration of Printer Setting MenuTCP/IP Setup NetWare Setup English French Italy German SpanishCMD Error Control Panel Setup Print QualityO Timeout ErrorNetwork Setup Functions of the Printer SettingSelect Language Timeout Print QualityError CMD ErrorTest Print Factory Default HelpStatus Monitor and Control Panel Status Monitor and Control Panel Contents of This Chapter Status Monitor and Control Panel Printer Setting tabConfiguration tab Status Monitor and Control PanelHow to Install Status Monitor and Control Panel Working EnvironmentFinishing the Status Monitor How to Operate the Status MonitorStarting the Status Monitor Restarting the Status MonitorShow/Hide the Status Monitor Case of Expanding the Display Display ChangeCase of Reducing the Display Starting the Control Panel Finishing the Control PanelSet Default Buttons of the Control PanelSettings of Paper Printer Setting Confirmation of Configurations Appendix a Trouble Shooting Appendix a Troubleshooting Error Message Error messages shown on the Status Monitor are as followsPrinter Controller does not respond to the Print command Basic TroubleshootingGeneral Problems of Printing OHT Film is not selectableAppendix a Troubleshooting You can not print the test printMemory Error / Memory Overflow / Overrun Duplex option is not displayedAppendix B Product Specifications Appendix B Product Specifications A4R A5R B5RAppendix B Product Specifications Index Index IndexIndex Page Konica Corporation