Intel MS-6112 manual Retention Mechanism Notch Hole

Page 15

CHAPTER 2	HARDWARE INSTALLATION

Step 3: Install the Heat Sink Support Base.

Look for the 2 holes across Slot 1, and match it with the 2 Heat Sink Support Base. Take note that one hole/base is bigger than the other.

Retention

Mechanism

Notch

Hole

PC-3742

Heat Sink

Support Base

Push the Heat Sink Support Base onto the mainboard, until you hear a click sound. Check for a perfect fit.

2-10

Image 15

Contents Introduction Mainboard Features Bios Mounting MS-6112 Central Processing Unit CPU Hardware InstallationCPU Installation Procedures OEM Pentium II processor Installation ProceduresRequired Things Hssbase Hsspin Rmamhsstop SLOT1 Pins Heat Sink Support Base Heat Sink Support Pin Heat Sink w/ Fan Chapter Hardware Installation Installation is now complete Boxed Pentium II processor Installation Procedures Retention Mechanism Notch Hole Intel Boxed PentiumTM Processor Heat Sink Support Processor Lock Heatsink Support PC-3745 CPU CPU Speed Setting SW1CPU Clock Generator Setting J10/J9 PSFAN1 CPU Fan Power Connectors JFAN/CFAN1/SFAN1Flash ROM Programming Voltage JMODE1 External Battery Connector JBAT1 Memory Bank Configuration Memory InstallationSingle Sided Dimm Double Sided Dimm Memory Installation ProceduresMemory Population Rules 1 EDO Dram Memory Addressing Case Connector JFP1 Keylock Reset SwitchPower LED Turbo LEDFloppy Disk Connector FDC Hard Disk Connectors IDE1 & IDE2 ATX 20-pin Power Connector JPWR1 Power SupplyRemote Power On/Off Switches JSW1/JSW2 IrDA Infrared Module Connector IR1 PIN Definition Signal Serial Port Connectors COM a & COM BParallel Port Connector LPT Keyboard Connector JKBMS1 Mouse Connector JKBMS1Mainboard provides aUHCIUniversal Host Controller Interface USB Connector USBPower Saving LED Connector JGL1 Special Jumpers J3/J4 AMI Bios User Guide Agioms Vxxx Enter Bios SetupAmibios Hiflex Setup Utilities Version Amibios Setup Standard Cmos Setup Standard Cmos SetupAmibios Setup Advanced Cmos Setup Advanced Cmos SetupFloppy Access Control Quick Boot1st Boot Device/2nd Boot Device/3rd Boot Device Try other Boot DevicesFloppy Drive Seek Boot up Num LockPassword Check Floppy Drive SwapInternal Cache/External Cache Boot to OS/2System Bios Cacheable Parity CheckChapter AMI Bios USER’S Guide Amibios Setup Advanced Chipset Setup Advanced Chipset SetupEDO Dram Speed ns Auto Configure EDO Dram TimingEDO RAS to CAS Delay Sdram RAS to CAS DelayVGA Frame Buffer Uswc Dram Integrity ModeSdram CAS Latency Sdram RAS Precharge TimeCPU To PCI IDE Posting PCI Frame Buffer UswcDram Refresh Queue Fixed Memory HolePIIX4 Passive Release PIIX4 Delayed TransactionAGP Aperture Size USB Passive ReleaseUSB Keyboard Legacy Support USB FunctionAmibios Setup Power Management Setup Power Management SetupHard Disk Power Down Mode Power Management/APMGreen PC Monitor Power State Video Power Down ModeModem Use IO Port Standby Time OutSuspend Time Out Throttle Slow Clock RatioPower Button Function RTC Alarm Resume From Soft-OffRing Resume from Soft-Off Amibios Setup PCI/PLUG and Play Setup PCI/Plug and Play SetupAllocate IRQ to PCI VGA PCI Latency Timer PCI ClocksPlug and Play Aware O/S PCI VGA Palette SnoopPCI IDE BusMaster Offboard PCI IDE CardOffboard PCI IDE Primary IRQ Offboard PCI IDE Secondary IRQ Reserved Memory Size/Reserved Memory Address DMA Channel 0/1/3/5/6/7Amibios Setup Peripheral Setup Peripheral SetupOnboard Serial Port A/Onboard Serial Port B Onboard FDCIR DMA Select IR Port SupportIR Base Address Select IR IRQ SelectParallel Port DMA Channel Parallel Port ModeEPP Version Parallel Port IRQAmibios Setup Hardware Monitor Setup Hardware Monitor Setup