Intel MS-6112 manual Remote Power On/Off Switches JSW1/JSW2

Page 33

CHAPTER 2	HARDWARE INSTALLATION

2.8-2 Remote Power On/Off Switches: JSW1/JSW2

Connect to a 2-pin push button switch. Every time the switch is shorted by pushing it once, the power supply will change its status from OFF to ON.

During ON stage, push once and the system goes to sleep mode: pushing it more than 4 seconds will change its status from ON to OFF. If you want to change the setup, you could go to the BIOS Power Management Setup.

This is used for ATX type power supply.

JSW1

JSW2

Note: The two switches are provided by the mainboard for your convenience, so you can use any of them. The two switches have the same feature.

2-28

Image 33

Contents Introduction Mainboard Features Bios Mounting MS-6112 Central Processing Unit CPU Hardware InstallationCPU Installation Procedures OEM Pentium II processor Installation ProceduresRequired Things Hssbase Hsspin Rmamhsstop SLOT1 Pins Heat Sink Support Base Heat Sink Support Pin Heat Sink w/ Fan Chapter Hardware Installation Installation is now complete Boxed Pentium II processor Installation Procedures Retention Mechanism Notch Hole Intel Boxed PentiumTM Processor Heat Sink Support Processor Lock Heatsink Support PC-3745 CPU CPU Speed Setting SW1CPU Clock Generator Setting J10/J9 PSFAN1 CPU Fan Power Connectors JFAN/CFAN1/SFAN1Flash ROM Programming Voltage JMODE1 External Battery Connector JBAT1 Memory Bank Configuration Memory InstallationSingle Sided Dimm Double Sided Dimm Memory Installation ProceduresMemory Population Rules 1 EDO Dram Memory Addressing Case Connector JFP1 Power LED Reset SwitchTurbo LED KeylockFloppy Disk Connector FDC Hard Disk Connectors IDE1 & IDE2 ATX 20-pin Power Connector JPWR1 Power SupplyRemote Power On/Off Switches JSW1/JSW2 IrDA Infrared Module Connector IR1 PIN Definition Signal Serial Port Connectors COM a & COM BParallel Port Connector LPT Keyboard Connector JKBMS1 Mouse Connector JKBMS1Mainboard provides aUHCIUniversal Host Controller Interface USB Connector USBPower Saving LED Connector JGL1 Special Jumpers J3/J4 AMI Bios User Guide Agioms Vxxx Enter Bios SetupAmibios Hiflex Setup Utilities Version Amibios Setup Standard Cmos Setup Standard Cmos SetupAmibios Setup Advanced Cmos Setup Advanced Cmos Setup1st Boot Device/2nd Boot Device/3rd Boot Device Quick BootTry other Boot Devices Floppy Access ControlPassword Check Boot up Num LockFloppy Drive Swap Floppy Drive SeekSystem Bios Cacheable Boot to OS/2Parity Check Internal Cache/External CacheChapter AMI Bios USER’S Guide Amibios Setup Advanced Chipset Setup Advanced Chipset SetupEDO RAS to CAS Delay Auto Configure EDO Dram TimingSdram RAS to CAS Delay EDO Dram Speed nsSdram CAS Latency Dram Integrity ModeSdram RAS Precharge Time VGA Frame Buffer UswcDram Refresh Queue PCI Frame Buffer UswcFixed Memory Hole CPU To PCI IDE PostingAGP Aperture Size PIIX4 Delayed TransactionUSB Passive Release PIIX4 Passive ReleaseUSB Keyboard Legacy Support USB FunctionAmibios Setup Power Management Setup Power Management SetupGreen PC Monitor Power State Power Management/APMVideo Power Down Mode Hard Disk Power Down ModeSuspend Time Out Standby Time OutThrottle Slow Clock Ratio Modem Use IO PortPower Button Function RTC Alarm Resume From Soft-OffRing Resume from Soft-Off Amibios Setup PCI/PLUG and Play Setup PCI/Plug and Play SetupPlug and Play Aware O/S PCI Latency Timer PCI ClocksPCI VGA Palette Snoop Allocate IRQ to PCI VGAPCI IDE BusMaster Offboard PCI IDE CardOffboard PCI IDE Primary IRQ Offboard PCI IDE Secondary IRQ Reserved Memory Size/Reserved Memory Address DMA Channel 0/1/3/5/6/7Amibios Setup Peripheral Setup Peripheral SetupOnboard Serial Port A/Onboard Serial Port B Onboard FDCIR Base Address Select IR Port SupportIR IRQ Select IR DMA SelectEPP Version Parallel Port ModeParallel Port IRQ Parallel Port DMA ChannelAmibios Setup Hardware Monitor Setup Hardware Monitor Setup