Intel GA-G1975X CPU Warning Temperature, CPU/POWER/SYSTEM FAN Fail Warning, CPU Smart FAN Control

Page 49

CPU Warning Temperature

60oC / 140oF Monitor CPU temperature at 60oC / 140oF.

70oC / 158oF Monitor CPU temperature at 70oC / 158oF.

80oC / 176oF Monitor CPU temperature at 80oC / 176oF.

90oC / 194oF Monitor CPU temperature at 90oC / 194oF.

Disabled Disable this function. (Default value)

CPU/POWER/SYSTEM FAN Fail Warning

Disabled	Disable fan fail warning function. (Default value)
Enabled	Enable fan fail warning function.

CPU Smart FAN Control

Disabled	Disable this function.
Enabled	When this function is enabled, CPU fan will run at different speed depending on
	CPU temperature. Users can adjust the fan speed with Easy Tune based on
	their requirements. (Default value)

CPU Smart FAN Mode

This option is available only when CPU Smart FAN Control is enabled.

Auto	BIOS autodetects the type of CPU fan you installed and sets the optimal CPU Smart
	FAN control mode for it. (Default value)
Voltage	Set to Voltage when you use a CPU fan with a 3-pin fan power cable.
PWM	Set to PWM when you use a CPU fan with a 4-pin fan power cable.

Note: In fact, the Voltage option can be used for CPU fans with 3-pin or 4-pin power cables. However, some 4-pin CPU fan power cables are not designed following Intel 4-Wire fans PWM control specifications. With such CPU fans, selecting PWM will not effectively reduce the fan speed.

English

- 49 -

BIOS Setup

Image 49

Contents GA-G1975X Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-G1975X GA-G1975X Motherboard LayoutBlock Diagram Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryBios English Installation of the CPU Installation of the CPU and HeatsinkHT functionality requirement content Installation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Configuring a Multi View System Configuring a Multi-Graphics Cards SystemBefore you begin Enabling CrossFire Mode Configuring an ATi CrossFireTM SystemI/O Back Panel Introduction ATX Power Connector Connectors IntroductionATX12V2X4 F11394 / F21394ATX12V2X4/ATX Power Connector 6 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector PCIE12V Power ConnectorIDE1 / IDE2 IDE Connector FDD Floppy ConnectorBattery SATAII01 / SATAII23 Sata 3Gb/s ConnectorFpanel Front Panel Jumper Cdin CD Faudio Front Audio ConnectorSpdifio Spdif In/Out USB1 / FUSB2 / Greenusb Front USB ConnectorRfid 16 F11394 / F21394 Ieee 1394 ConnectorCI Chassis Intrusion, Case Open PwrledSurcen Surround Center Connector Coma Coma Connector22 PW1 / PW2 English English Main Menu Status Page Setup Menu / Option Page Setup MenuF12 For Boot Menu Main Menu For example Bios Ver. F1„ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 0 Master, Slave TimeIDE Channel 2/3 Master Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onBase Memory MemoryExtended Memory Total MemoryBios Flash Protection Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Num-Lock Boot Up Floppy SeekPassword Check Interrupt ModeDram Data Integrity Mode Delay For HDD SecsLimit Cpuid Max. to No-Execute Memory Protect NoteSata Port 0/2 Set to Pata IDE Set toSata Port 1/3 Set to USB Controller OnBoard LAN Boot ROMUSB 2.0 Controller USB Keyboard SupportPower On By Mouse Resume by AlarmKB Power on Password Power On By KeyboardPCI Latency Timer CLK AC Back FunctionCurrent CPU/POWER/SYSTEM FAN Speed RPM Current CPU TemperaturePCI 1 IRQ Assignment PCI 2 IRQ AssignmentCPU/POWER/SYSTEM FAN Fail Warning CPU Warning TemperatureCPU Smart FAN Mode CPU Smart FAN ControlM. Note MB Intelligent TweakerM.I.TCPU Clock Ratio Note A.2 Robust Graphics BoosterCPU Host Clock Control CPU Host FrequencyMhzDimm OverVoltage Control Memory Frequency MhzPCI-E OverVoltage Control FSB OverVoltage ControlActive to Precharge Delay Dram RAS# to CAS# DelayRefresh Mode Select CAS Latency TimeSelect Language Top PerformanceLoad Optimized Defaults Load Fail-Safe DefaultsSave & Exit Setup Set Supervisor/User PasswordExit Without Saving English Install Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionHow to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations What is Dual Bios Technology? Flash Bios Method IntroductionHow to use Dual Bios and Q-Flash Utility? Boot From Main BIOSDefault, Backup Bios Wide Range Protection DisableDefault, EnableAuto Recovery EnableDefault, Disable Halt On Error DisableDefault, EnableBefore You Begin Method 1 Q-FlashTMUtilityTask menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Press Y on your keyboard to load defaults English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish English Installing Sata hard drives in your computer RAID Step Save and exit Bios Setup Create RAID Volume¡G Configuring RAID set in RAID BiosEnter Create Volume Delete RAID Volume Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Accessing Creative Speaker Settings Configuring Multi-Channel Speakers with Audio Combo Kit Channel Speaker ConfigurationsInstalling Audio Combo Kit Front Speaker Out Rear Speaker Out Front Speaker Out Enabling Digital Output English DTS Introduction Using Creative Built-in decoder Device ControlEnglish English Using External Decoder Decoding using SoftDVD player DTS Neo6 Launching DTS Neo6 Settings To launch DTS Neo6 SettingsFinal Word AMI Bios Beep Codes TroubleshootingPost hex Description Post Error CodeEnglish E8POST.ASM starts English GA-G1975X Motherboard 108 109 GA-G1975X Motherboard 110 Taiwan Headquarters Contact UsGA-G1975X Motherboard 112