Intel GA-G1975X USB Controller, USB 2.0 Controller, USB Keyboard Support, USB Mouse Support, Lock

Page 45

USB Controller

Enabled	Enable USB controller. (Default value)
Disabled	Disable USB controller.

USB 2.0 Controller

Disable this function if you are not using onboard USB 2.0 feature.

Enabled	Enable USB 2.0 controller. (Default value)
Disabled	Disable USB 2.0 controller.

USB Keyboard Support

Enabled	Enable USB keyboard support.
Disabled	Disable USB keyboard support. (Default value)

USB Mouse Support

Enabled	Enable USB mouse support.
Disabled	Disable USB mouse support. (Default value)

Onboard H/W Sound

Enabled	Enable onboard sound. (Default value)
Disabled	Disable this function.

Onboard H/W 1394

Enabled	Enable onboard IEEE 1394 function. (Default value)
Disabled	Disable this function.

Onboard H/W GigaATA

Enabled	Enable onboard H/W GigaATA function. (Default value)
Disabled	Disable this function.

Onboard H/W LAN

Enabled	Enable onboard H/W LAN function. (Default value)
Disabled	Disable this function.

OnBoard LAN Boot ROM

This function decide whether to invoke the boot ROM of the onboard LAN chip.

Enabled	Enable this function.
Disabled	Disable this function. (Default value)

Onboard Serial Port 1

Auto	BIOS will automatically setup the port 1 address.
3F8/IRQ4	Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)
2F8/IRQ3	Enable onboard Serial port 1 and address is 2F8/IRQ3.
3E8/IRQ4	Enable onboard Serial port 1 and address is 3E8/IRQ4.
2E8/IRQ3	Enable onboard Serial port 1 and address is 2E8/IRQ3.
Disabled	Disable onboard Serial port 1.

i-Lock

Enabled	Enable the i-Lock function. (Default value)
Disabled	Disable the i-Lock function.

English

- 45 -

BIOS Setup

Image 45

Contents GA-G1975X Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-G1975X GA-G1975X Motherboard LayoutBlock Diagram Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryBios English Installation of the CPU and Heatsink Installation of the CPUHT functionality requirement content Installation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Configuring a Multi-Graphics Cards System Configuring a Multi View SystemBefore you begin Enabling CrossFire Mode Configuring an ATi CrossFireTM SystemI/O Back Panel Introduction ATX Power Connector Connectors IntroductionATX12V2X4 F11394 / F21394ATX12V2X4/ATX Power Connector 6 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector PCIE12V Power ConnectorIDE1 / IDE2 IDE Connector FDD Floppy ConnectorBattery SATAII01 / SATAII23 Sata 3Gb/s ConnectorFpanel Front Panel Jumper Cdin CD Faudio Front Audio ConnectorSpdifio Spdif In/Out USB1 / FUSB2 / Greenusb Front USB ConnectorRfid 16 F11394 / F21394 Ieee 1394 ConnectorCI Chassis Intrusion, Case Open PwrledSurcen Surround Center Connector Coma Coma Connector22 PW1 / PW2 English English Main Menu Status Page Setup Menu / Option Page Setup MenuF12 For Boot Menu Main Menu For example Bios Ver. F1„ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 0 Master, Slave TimeIDE Channel 2/3 Master Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onBase Memory MemoryExtended Memory Total MemoryHard Disk Boot Priority Bios Flash ProtectionFirst / Second / Third Boot Device Boot Up Num-Lock Boot Up Floppy SeekPassword Check Interrupt ModeDram Data Integrity Mode Delay For HDD SecsLimit Cpuid Max. to No-Execute Memory Protect NotePata IDE Set to Sata Port 0/2 Set toSata Port 1/3 Set to USB Controller OnBoard LAN Boot ROMUSB 2.0 Controller USB Keyboard SupportPower On By Mouse Resume by AlarmKB Power on Password Power On By KeyboardPCI Latency Timer CLK AC Back FunctionCurrent CPU/POWER/SYSTEM FAN Speed RPM Current CPU TemperaturePCI 1 IRQ Assignment PCI 2 IRQ AssignmentCPU/POWER/SYSTEM FAN Fail Warning CPU Warning TemperatureCPU Smart FAN Mode CPU Smart FAN ControlMB Intelligent TweakerM.I.T M. NoteCPU Clock Ratio Note A.2 Robust Graphics BoosterCPU Host Clock Control CPU Host FrequencyMhzDimm OverVoltage Control Memory Frequency MhzPCI-E OverVoltage Control FSB OverVoltage ControlActive to Precharge Delay Dram RAS# to CAS# DelayRefresh Mode Select CAS Latency TimeSelect Language Top PerformanceLoad Optimized Defaults Load Fail-Safe DefaultsSave & Exit Setup Set Supervisor/User PasswordExit Without Saving English Install Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionXpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction What is Dual Bios Technology?How to use Dual Bios and Q-Flash Utility? Boot From Main BIOSDefault, Backup Bios Wide Range Protection DisableDefault, EnableAuto Recovery EnableDefault, Disable Halt On Error DisableDefault, EnableBefore You Begin Method 1 Q-FlashTMUtilityTask menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Press Y on your keyboard to load defaults English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish English Installing Sata hard drives in your computer RAID Step Save and exit Bios Setup Create RAID Volume¡G Configuring RAID set in RAID BiosEnter Create Volume Delete RAID Volume Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Accessing Creative Speaker Settings Channel Speaker Configurations Configuring Multi-Channel Speakers with Audio Combo KitInstalling Audio Combo Kit Front Speaker Out Rear Speaker Out Front Speaker Out Enabling Digital Output English DTS Introduction Using Creative Built-in decoder Device ControlEnglish English Using External Decoder Decoding using SoftDVD player DTS Neo6 Launching DTS Neo6 Settings To launch DTS Neo6 SettingsFinal Word AMI Bios Beep Codes TroubleshootingPost hex Description Post Error CodeEnglish E8POST.ASM starts English GA-G1975X Motherboard 108 109 GA-G1975X Motherboard 110 Taiwan Headquarters Contact UsGA-G1975X Motherboard 112