Intel GA-G1975X PCIE12V Power Connector, Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector

Page 23

3)PCIE_12V (Power Connector)

The PCIE_12V power connector supplies extra power to the PCIE x 16 slot. Connect this connector depending on your system requirements.

1

PIin No.	Definition
1	NC
2	GND
3	GND
4	+12V

4/5/6) CPU_FAN / SYS_FAN / PWR_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin (only for CPU_FAN) power connector and possesses a foolproof connection design.

Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND).

Please remember to connect the power to the cooler to prevent system overheating and failure. Caution!

Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.

				Pin No.	Definition
				Pin No.	Definition
				1	GND
				1	GND
				2	+12V
				2	+12V
	1
	1			3	Sense
	CPU_FAN
	CPU_FAN			4	Speed Control
				4	Speed Control
	1				(Only for CPU_FAN)






	SYS_FAN / PWR_FAN

English

- 23 -

Hardware Installation

Image 23

Contents GA-G1975X Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-G1975X GA-G1975X Motherboard LayoutBlock Diagram Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryBios English HT functionality requirement content Installation of the CPU and HeatsinkInstallation of the CPU Installation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Before you begin Configuring a Multi-Graphics Cards SystemConfiguring a Multi View System Enabling CrossFire Mode Configuring an ATi CrossFireTM SystemI/O Back Panel Introduction F11394 / F21394 Connectors IntroductionATX Power Connector ATX12V2X4ATX12V2X4/ATX Power Connector 6 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector PCIE12V Power ConnectorIDE1 / IDE2 IDE Connector FDD Floppy ConnectorBattery SATAII01 / SATAII23 Sata 3Gb/s ConnectorFpanel Front Panel Jumper Cdin CD Faudio Front Audio ConnectorSpdifio Spdif In/Out USB1 / FUSB2 / Greenusb Front USB ConnectorRfid 16 F11394 / F21394 Ieee 1394 ConnectorCI Chassis Intrusion, Case Open PwrledSurcen Surround Center Connector Coma Coma Connector22 PW1 / PW2 English English Main Menu Status Page Setup Menu / Option Page Setup MenuF12 For Boot Menu Main Menu For example Bios Ver. F1„ PnP/PCI Configuration „ Standard Cmos Features„ Advanced Bios Features „ Power Management SetupIDE Channel 0 Master, Slave TimeHalt on Floppy 3 Mode Support for Japan AreaIDE Channel 2/3 Master Drive a / Drive BTotal Memory MemoryBase Memory Extended MemoryFirst / Second / Third Boot Device Hard Disk Boot PriorityBios Flash Protection Interrupt Mode Boot Up Floppy SeekBoot Up Num-Lock Password CheckNo-Execute Memory Protect Note Delay For HDD SecsDram Data Integrity Mode Limit Cpuid Max. toSata Port 1/3 Set to Pata IDE Set toSata Port 0/2 Set to USB Keyboard Support OnBoard LAN Boot ROMUSB Controller USB 2.0 ControllerPower On By Mouse Resume by AlarmAC Back Function Power On By KeyboardKB Power on Password PCI Latency Timer CLKPCI 2 IRQ Assignment Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM PCI 1 IRQ AssignmentCPU Smart FAN Control CPU Warning TemperatureCPU/POWER/SYSTEM FAN Fail Warning CPU Smart FAN ModeCPU Clock Ratio Note MB Intelligent TweakerM.I.TM. Note CPU Host FrequencyMhz Robust Graphics BoosterA.2 CPU Host Clock ControlFSB OverVoltage Control Memory Frequency MhzDimm OverVoltage Control PCI-E OverVoltage ControlCAS Latency Time Dram RAS# to CAS# DelayActive to Precharge Delay Refresh Mode SelectSelect Language Top PerformanceLoad Optimized Defaults Load Fail-Safe DefaultsSave & Exit Setup Set Supervisor/User PasswordExit Without Saving English Install Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionSystem requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions How to use Dual Bios and Q-Flash Utility? Flash Bios Method IntroductionWhat is Dual Bios Technology? Halt On Error DisableDefault, Enable Wide Range Protection DisableDefault, EnableBoot From Main BIOSDefault, Backup Bios Auto Recovery EnableDefault, DisableBefore You Begin Method 1 Q-FlashTMUtilityTask menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Press Y on your keyboard to load defaults English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish English Installing Sata hard drives in your computer RAID Step Save and exit Bios Setup Create RAID Volume¡G Configuring RAID set in RAID BiosEnter Create Volume Delete RAID Volume Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Accessing Creative Speaker Settings Installing Audio Combo Kit Channel Speaker ConfigurationsConfiguring Multi-Channel Speakers with Audio Combo Kit Front Speaker Out Rear Speaker Out Front Speaker Out Enabling Digital Output English DTS Introduction Using Creative Built-in decoder Device ControlEnglish English Using External Decoder Decoding using SoftDVD player DTS Neo6 Launching DTS Neo6 Settings To launch DTS Neo6 SettingsFinal Word AMI Bios Beep Codes TroubleshootingPost hex Description Post Error CodeEnglish E8POST.ASM starts English GA-G1975X Motherboard 108 109 GA-G1975X Motherboard 110 Taiwan Headquarters Contact UsGA-G1975X Motherboard 112