Intel GA-8IPXDR-E user manual Install expansion cards

Page 17

Hardware Installation Process

Step 3: Install expansion cards

1.Read the related expansion card’s instruction document before install the expansion card into the computer.

2.Remove your computer’s chassis cover, screws and slot bracket from the computer.

3.Press the expansion card firmly into expansion slot in motherboard.

4.Be sure the metal contacts on the card are indeed seated in the slot.

5.Replace the screw to secure the slot bracket of the expansion card.

6.Replace your computer’s chassis cover.

7.Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.

8.Install related driver from the operating system.

1 7

Image 17
Contents USER’S Manual Table of Content Technical Reference Item Checklist Installing the motherboard to the chassis… Introduction Bios GA-8IPXDR-EC Motherboard Layout Step Hardware Installation ProcessInstalling Motherboard to the Chassis Install the Central Processing Unit CPUFor socket 603 / 400MHz CPU InstallationFor socket 604 / 533MHz CPU Heat Sink Installation GA-8IPXDR-EC Motherboard Install memory modules Installation Step Install expansion cards I/O Back Panel Introduction PS/2 Keyboard and PS/2 Mouse ConnectorUSB Connector \ LAN1 / LAN2 Port ZParallel Port / Serial Port / VGA Port LPT/COMA/VGAConnectors Introduction ATX1 ATX1 Power ATX3 2x12 Pin ATX PowerJ30/J32 CPU FAN Connector ATX2 +12V Power ConnectorJ31 Power FAN Connector J33/J34 System FAN ConnectorCOM 2 Connector J18 Wake On LAN ConnectorIDE1/IDE2 IDE1 / IDE2 ConnectorPrimary/Secondary SCSI1/2 ConnectorCase Open FDD1 Floppy ConnectorUSB1 Front USB Connector J20 Front Panel Connector-- Power button and Power LEDBT1 Battery Ipmicon Ipmi ConnectorJPSPK+ JPHD+ Jprst Jphd Jpspk Fpanel connectorJumper Setting Introduction JP 9 Front Side USB Wake Up Function JP 1 Onboard Scsi Function JP 8 Onboard VGA FunctonJP 10 Rear Side USB Wake Up Function DefaultJP17 JP18 14 JP22 On Board Scsi Channel B Terminator Function 13 JP21 On Board Scsi Channel a Terminator FunctionClrcmos Clear Cmos Function Bios Setup Boot Status Page Setup Menu / Option Page Setup MenuMainMenu MainSystem Time System DateIDE Primary Master, Slave / Secondary Master, Slave FloppyDriveA/BSystemInformation About This Section Advanced AdvancedIndicates Display only AdvancedConfiguration` Quick Boot ` Console Redirect ` MPS Version for O.S` Hyper Threading Chipset Configuration` ClkGen Spread Spectrum ` PME Event Wake Up PowerManagement Configuration` System After AC Back ` Relaxed Ordering PCI-X Configuration` Data Parity Error Recovery ` OnBoard FDC Peripheral Configuration` OnBoard IDE ` OnBoard Parallel Port ` OnBoard Serial Port a` OnBoard Serial Port B Normal ` Parallel Port ModeBi-Directional ` Parallel Port IRQ` OnBoard Scsi ` OnBoard Gigabit LANsCPU0 FAN RPM CPU1 FAN HardwareMonitorConfiguration ` System FAN ` Power FAN 1/2` CPU 0 / 1 FAN About This Section Security Set Supervisor PasswordPassword Check Set User Password` 1st / 2nd / 3 rd Boot Device About This Section BootBoot Device Priority ` OnBoard LAN Boot ROM Exit Exit Saving Changes Load Default SettingsExit Discarding Changes Load Original ValuesTechnical Reference Appendix Appendix a Intel Network Driver InstallationGA-8IPXDR-EC Motherboard Appendix B INF Update Installation Driver for chipset Appendix C ATI Rage XL VGA Driver Installation Appexdix D Adaptec Scsi Driver Installation Http//networking.gigabyte.com.tw Appendix E Utilites InstallationAppendix F About Updateing Latest version of Bios Appendix G Ipmi Connector Pin Definition Appendix H Acronyms LAN Technical Support/RMA Sheet