Intel GA-8IPXDR-E user manual JP 1 Onboard Scsi Function JP 8 Onboard VGA Functon

Page 31

Jumper Setting

1) JP 1 (Onboard SCSI Function)

1

1

2) JP 8 (Onboard VGA Functon)

1-2 close: SCSI Enabled (Default)

2-3 close: SCSI Disabled

1

1-2 close: VGA Enabled (Default)

1

2-3 close: VGA Disabled

3) JP 9 (Front Side USB Wake Up Function)

1

1

1-2 close: Front USB wake up function disabled (Default)

2-3 close: Front USB wake up functionenabled

3 1

Image 31
Contents USER’S Manual Table of Content Technical Reference Item Checklist Installing the motherboard to the chassis… Introduction Bios GA-8IPXDR-EC Motherboard Layout Step Hardware Installation ProcessInstalling Motherboard to the Chassis Install the Central Processing Unit CPUFor socket 603 / 400MHz CPU InstallationFor socket 604 / 533MHz CPU Heat Sink Installation GA-8IPXDR-EC Motherboard Install memory modules Installation Step Install expansion cards USB Connector PS/2 Keyboard and PS/2 Mouse ConnectorI/O Back Panel Introduction \ LAN1 / LAN2 Port ZParallel Port / Serial Port / VGA Port LPT/COMA/VGAConnectors Introduction ATX1 ATX1 Power ATX3 2x12 Pin ATX PowerJ30/J32 CPU FAN Connector ATX2 +12V Power ConnectorJ31 Power FAN Connector J33/J34 System FAN ConnectorCOM 2 Connector J18 Wake On LAN ConnectorIDE1/IDE2 IDE1 / IDE2 ConnectorPrimary/Secondary SCSI1/2 ConnectorCase Open FDD1 Floppy ConnectorUSB1 Front USB Connector J20 Front Panel Connector-- Power button and Power LEDBT1 Battery Ipmicon Ipmi ConnectorJPSPK+ JPHD+ Jprst Jphd Jpspk Fpanel connectorJumper Setting Introduction JP 9 Front Side USB Wake Up Function JP 1 Onboard Scsi Function JP 8 Onboard VGA FunctonJP 10 Rear Side USB Wake Up Function DefaultJP17 JP18 14 JP22 On Board Scsi Channel B Terminator Function 13 JP21 On Board Scsi Channel a Terminator FunctionClrcmos Clear Cmos Function Bios Setup Main Status Page Setup Menu / Option Page Setup MenuBoot MainMenuSystem Time System DateIDE Primary Master, Slave / Secondary Master, Slave FloppyDriveA/BSystemInformation About This Section Advanced Advanced` Quick Boot AdvancedConfigurationIndicates Display only ` Console Redirect ` MPS Version for O.S` ClkGen Spread Spectrum Chipset Configuration` Hyper Threading ` System After AC Back PowerManagement Configuration` PME Event Wake Up ` Data Parity Error Recovery PCI-X Configuration` Relaxed Ordering ` OnBoard IDE Peripheral Configuration` OnBoard FDC ` OnBoard Serial Port B ` OnBoard Serial Port a` OnBoard Parallel Port ` Parallel Port IRQ ` Parallel Port ModeNormal Bi-Directional` OnBoard Scsi ` OnBoard Gigabit LANsCPU0 FAN RPM CPU1 FAN HardwareMonitorConfiguration ` CPU 0 / 1 FAN ` Power FAN 1/2` System FAN About This Section Security Set Supervisor PasswordPassword Check Set User PasswordBoot Device Priority About This Section Boot` 1st / 2nd / 3 rd Boot Device ` OnBoard LAN Boot ROM Exit Load Original Values Load Default SettingsExit Saving Changes Exit Discarding ChangesTechnical Reference Appendix Appendix a Intel Network Driver InstallationGA-8IPXDR-EC Motherboard Appendix B INF Update Installation Driver for chipset Appendix C ATI Rage XL VGA Driver Installation Appexdix D Adaptec Scsi Driver Installation Appendix F About Updateing Latest version of Bios Appendix E Utilites InstallationHttp//networking.gigabyte.com.tw Appendix G Ipmi Connector Pin Definition Appendix H Acronyms LAN Technical Support/RMA Sheet