Intel GA-8IPXDR-E user manual Set User Password, Password Check

Page 55

BIOS Setup

Set User Password

You can only enter but do not have the right to change the options of the setup menus. When you select this function, the following message will appear at the center of the screen o assist you in creating a password.

Type the password up to 6 characters in lengh and press <Enter>. The password typed now will clear any previously entered password from the CMOS memory. You will be asked to confirm the entered password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a specified password.

Password Check

`Setup will check password while invlolking setup. (Default Value)

`Always will check the password while involking setup as well as on each boot.

5 5

Image 55
Contents USER’S Manual Table of Content Technical Reference Item Checklist Installing the motherboard to the chassis… Introduction Bios GA-8IPXDR-EC Motherboard Layout Step Hardware Installation ProcessInstalling Motherboard to the Chassis Install the Central Processing Unit CPUFor socket 603 / 400MHz CPU InstallationFor socket 604 / 533MHz CPU Heat Sink Installation GA-8IPXDR-EC Motherboard Install memory modules Installation Step Install expansion cards USB Connector PS/2 Keyboard and PS/2 Mouse ConnectorI/O Back Panel Introduction \ LAN1 / LAN2 Port ZParallel Port / Serial Port / VGA Port LPT/COMA/VGAConnectors Introduction ATX1 ATX1 Power ATX3 2x12 Pin ATX PowerJ30/J32 CPU FAN Connector ATX2 +12V Power ConnectorJ31 Power FAN Connector J33/J34 System FAN ConnectorCOM 2 Connector J18 Wake On LAN ConnectorIDE1/IDE2 IDE1 / IDE2 ConnectorPrimary/Secondary SCSI1/2 ConnectorCase Open FDD1 Floppy ConnectorUSB1 Front USB Connector J20 Front Panel Connector-- Power button and Power LEDBT1 Battery Ipmicon Ipmi ConnectorJPSPK+ JPHD+ Jprst Jphd Jpspk Fpanel connectorJumper Setting Introduction JP 9 Front Side USB Wake Up Function JP 1 Onboard Scsi Function JP 8 Onboard VGA FunctonJP 10 Rear Side USB Wake Up Function DefaultJP17 JP18 14 JP22 On Board Scsi Channel B Terminator Function 13 JP21 On Board Scsi Channel a Terminator FunctionClrcmos Clear Cmos Function Bios Setup Main Status Page Setup Menu / Option Page Setup MenuBoot MainMenuSystem Time System DateIDE Primary Master, Slave / Secondary Master, Slave FloppyDriveA/BSystemInformation About This Section Advanced Advanced` Quick Boot AdvancedConfigurationIndicates Display only ` Console Redirect ` MPS Version for O.S` ClkGen Spread Spectrum Chipset Configuration` Hyper Threading ` System After AC Back PowerManagement Configuration` PME Event Wake Up ` Data Parity Error Recovery PCI-X Configuration` Relaxed Ordering ` OnBoard IDE Peripheral Configuration` OnBoard FDC ` OnBoard Serial Port B ` OnBoard Serial Port a` OnBoard Parallel Port ` Parallel Port IRQ ` Parallel Port ModeNormal Bi-Directional` OnBoard Scsi ` OnBoard Gigabit LANsCPU0 FAN RPM CPU1 FAN HardwareMonitorConfiguration ` CPU 0 / 1 FAN ` Power FAN 1/2` System FAN About This Section Security Set Supervisor PasswordPassword Check Set User PasswordBoot Device Priority About This Section Boot` 1st / 2nd / 3 rd Boot Device ` OnBoard LAN Boot ROM Exit Load Original Values Load Default SettingsExit Saving Changes Exit Discarding ChangesTechnical Reference Appendix Appendix a Intel Network Driver InstallationGA-8IPXDR-EC Motherboard Appendix B INF Update Installation Driver for chipset Appendix C ATI Rage XL VGA Driver Installation Appexdix D Adaptec Scsi Driver Installation Appendix F About Updateing Latest version of Bios Appendix E Utilites InstallationHttp//networking.gigabyte.com.tw Appendix G Ipmi Connector Pin Definition Appendix H Acronyms LAN Technical Support/RMA Sheet