Intel GA-8IPXDR-E user manual Hardware Installation Process, Step

Page 9

Hardware Installation Process

Chapter 2 Hardware Installation Process

To set up your computer, you must complete the following setups:

Step 1- Install the Central Processing Unit (CPU) Step 2- Install memory modules

Step 3- Install expansion cards

Step 4- Connect ribbon cables, cabinet wires, and power supply Step 5- Setup BIOS software

Step 6- Install supporting software tools

Step 4

Step 5

Step 4

Step 3

Step 4

Step 4

Step1

Step 4

 

 

Step 2

Step 4

9

Image 9
Contents USER’S Manual Table of Content Technical Reference Item Checklist Installing the motherboard to the chassis… Introduction Bios GA-8IPXDR-EC Motherboard Layout Step Hardware Installation ProcessInstalling Motherboard to the Chassis Install the Central Processing Unit CPUFor socket 603 / 400MHz CPU InstallationFor socket 604 / 533MHz CPU Heat Sink Installation GA-8IPXDR-EC Motherboard Install memory modules Installation Step Install expansion cards PS/2 Keyboard and PS/2 Mouse Connector USB ConnectorI/O Back Panel Introduction \ LAN1 / LAN2 Port ZParallel Port / Serial Port / VGA Port LPT/COMA/VGAConnectors Introduction ATX1 ATX1 Power ATX3 2x12 Pin ATX PowerJ30/J32 CPU FAN Connector ATX2 +12V Power ConnectorJ31 Power FAN Connector J33/J34 System FAN ConnectorCOM 2 Connector J18 Wake On LAN ConnectorIDE1/IDE2 IDE1 / IDE2 ConnectorPrimary/Secondary SCSI1/2 ConnectorCase Open FDD1 Floppy ConnectorUSB1 Front USB Connector J20 Front Panel Connector-- Power button and Power LEDBT1 Battery Ipmicon Ipmi ConnectorJPSPK+ JPHD+ Jprst Jphd Jpspk Fpanel connectorJumper Setting Introduction JP 9 Front Side USB Wake Up Function JP 1 Onboard Scsi Function JP 8 Onboard VGA FunctonJP 10 Rear Side USB Wake Up Function DefaultJP17 JP18 14 JP22 On Board Scsi Channel B Terminator Function 13 JP21 On Board Scsi Channel a Terminator FunctionClrcmos Clear Cmos Function Bios Setup Boot Status Page Setup Menu / Option Page Setup MenuMainMenu MainSystem Time System DateIDE Primary Master, Slave / Secondary Master, Slave FloppyDriveA/BSystemInformation About This Section Advanced AdvancedAdvancedConfiguration ` Quick BootIndicates Display only ` Console Redirect ` MPS Version for O.SChipset Configuration ` ClkGen Spread Spectrum` Hyper Threading PowerManagement Configuration ` System After AC Back` PME Event Wake Up PCI-X Configuration ` Data Parity Error Recovery` Relaxed Ordering Peripheral Configuration ` OnBoard IDE` OnBoard FDC ` OnBoard Serial Port a ` OnBoard Serial Port B` OnBoard Parallel Port Normal ` Parallel Port ModeBi-Directional ` Parallel Port IRQ` OnBoard Scsi ` OnBoard Gigabit LANsCPU0 FAN RPM CPU1 FAN HardwareMonitorConfiguration ` Power FAN 1/2 ` CPU 0 / 1 FAN` System FAN About This Section Security Set Supervisor PasswordPassword Check Set User PasswordAbout This Section Boot Boot Device Priority` 1st / 2nd / 3 rd Boot Device ` OnBoard LAN Boot ROM Exit Exit Saving Changes Load Default SettingsExit Discarding Changes Load Original ValuesTechnical Reference Appendix Appendix a Intel Network Driver InstallationGA-8IPXDR-EC Motherboard Appendix B INF Update Installation Driver for chipset Appendix C ATI Rage XL VGA Driver Installation Appexdix D Adaptec Scsi Driver Installation Appendix E Utilites Installation Appendix F About Updateing Latest version of BiosHttp//networking.gigabyte.com.tw Appendix G Ipmi Connector Pin Definition Appendix H Acronyms LAN Technical Support/RMA Sheet