Intel GA-8IPXDR-E user manual J20 Front Panel Connector-- Power button and Power LED

Page 27

GA-8IPXDR-E(C) Motherboard

N) J20 (Front Panel Connector-- Power button and Power LED)

1

20

Pin No.

Definition

17

PWR LED+

18

PWR LED-

19

PWR BTN+

20

PWR BTN-

H) USB1 (Front USB Connector)

1

Pin No.

Definition

1

Power

 

2

GND

 

3

USBD2-

 

4

NC

 

5

USBD2+

 

6

USBD3+

 

7

NC

 

8

USBD3-

 

9

GND

 

10

Power

 

Be careful with the polarity of the front panel USB connector. Check the pin assignment while you connect the front panel USB cable. Please contact your nearest dealer for optional front panel USB cable.

2 7

Image 27
Contents USER’S Manual Table of Content Technical Reference Item Checklist Installing the motherboard to the chassis… Introduction Bios GA-8IPXDR-EC Motherboard Layout Step Hardware Installation ProcessInstalling Motherboard to the Chassis Install the Central Processing Unit CPUFor socket 603 / 400MHz CPU InstallationFor socket 604 / 533MHz CPU Heat Sink Installation GA-8IPXDR-EC Motherboard Install memory modules Installation Step Install expansion cards PS/2 Keyboard and PS/2 Mouse Connector USB ConnectorI/O Back Panel Introduction \ LAN1 / LAN2 Port ZParallel Port / Serial Port / VGA Port LPT/COMA/VGAConnectors Introduction ATX1 ATX1 Power ATX3 2x12 Pin ATX PowerJ30/J32 CPU FAN Connector ATX2 +12V Power ConnectorJ31 Power FAN Connector J33/J34 System FAN ConnectorCOM 2 Connector J18 Wake On LAN ConnectorIDE1/IDE2 IDE1 / IDE2 ConnectorPrimary/Secondary SCSI1/2 ConnectorCase Open FDD1 Floppy ConnectorUSB1 Front USB Connector J20 Front Panel Connector-- Power button and Power LEDBT1 Battery Ipmicon Ipmi ConnectorJPSPK+ JPHD+ Jprst Jphd Jpspk Fpanel connectorJumper Setting Introduction JP 9 Front Side USB Wake Up Function JP 1 Onboard Scsi Function JP 8 Onboard VGA FunctonJP 10 Rear Side USB Wake Up Function DefaultJP17 JP18 14 JP22 On Board Scsi Channel B Terminator Function 13 JP21 On Board Scsi Channel a Terminator FunctionClrcmos Clear Cmos Function Bios Setup Main Status Page Setup Menu / Option Page Setup MenuBoot MainMenuSystem Time System DateIDE Primary Master, Slave / Secondary Master, Slave FloppyDriveA/BSystemInformation About This Section Advanced AdvancedAdvancedConfiguration ` Quick BootIndicates Display only ` Console Redirect ` MPS Version for O.SChipset Configuration ` ClkGen Spread Spectrum` Hyper Threading PowerManagement Configuration ` System After AC Back` PME Event Wake Up PCI-X Configuration ` Data Parity Error Recovery` Relaxed Ordering Peripheral Configuration ` OnBoard IDE` OnBoard FDC ` OnBoard Serial Port a ` OnBoard Serial Port B` OnBoard Parallel Port ` Parallel Port IRQ ` Parallel Port ModeNormal Bi-Directional` OnBoard Scsi ` OnBoard Gigabit LANsCPU0 FAN RPM CPU1 FAN HardwareMonitorConfiguration ` Power FAN 1/2 ` CPU 0 / 1 FAN` System FAN About This Section Security Set Supervisor PasswordPassword Check Set User PasswordAbout This Section Boot Boot Device Priority` 1st / 2nd / 3 rd Boot Device ` OnBoard LAN Boot ROM Exit Load Original Values Load Default SettingsExit Saving Changes Exit Discarding ChangesTechnical Reference Appendix Appendix a Intel Network Driver InstallationGA-8IPXDR-EC Motherboard Appendix B INF Update Installation Driver for chipset Appendix C ATI Rage XL VGA Driver Installation Appexdix D Adaptec Scsi Driver Installation Appendix E Utilites Installation Appendix F About Updateing Latest version of BiosHttp//networking.gigabyte.com.tw Appendix G Ipmi Connector Pin Definition Appendix H Acronyms LAN Technical Support/RMA Sheet