Intel GA-8I915MK-GV user manual Fpanel Front Panel Connector

Page 21

8)F_PANEL (Front Panel Connector)

Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassis front panel to the F_PANEL connector according to the pin assignments below.

Speaker Connector

20 19

SPEAK-

Power Switch

Message LED/

Power/

Sleep LED

SPEAK+

Reset Switch

PW-

NCRES+

PW+

RES-

MSG-

HD-

MSG+

HD+

2

1

 

IDE Hard Disk

 

Active LED

HD (IDE Hard Disk Active LED)

Pin 1: LED anode(+)

 

Pin 2: LED cathode(-)

SPEAK (Speaker Connector)

Pin 1: Power

 

Pin 2- Pin 3: NC

 

Pin 4: Data(-)

RES (Reset Switch)

Open: Normal

 

Close: Reset Hardware System

PW (Power Switch)

Open: Normal

 

Close: Power On/Off

MSG(Message LED/Power/Sleep LED)

Pin 1: LED anode(+)

 

Pin 2: LED cathode(-)

NC

NC

English

- 21 -

Hardware Installation

Image 21
Contents GA-8I915MK-GV Motherboard Product Manual Classification CopyrightTable of Contents Install Drivers 8I915MK-GV GA-8I915MK-GV Motherboard LayoutBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion CardsI/O Back Panel Introduction English Connectors IntroductionATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0/SATA1 Serial ATA Connector IDE1 IDE ConnectorFpanel Front Panel Connector Pwrled Faudio Front Audio Panel ConnectorAuxin AUX In Connector Cdin CD in ConnectorSurcen Spdifio Spdif In/ OutComb Comb Connector FUSB1 / FUSB2 Front USB ConnectorsClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBAT Battery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F1 Standard Cmos Features IDE Channel 0 Master, Slave Floppy 3 Mode Support for Japan AreaIDE Channel 2/3 Master, Slave Drive a / Drive BMemory Halt onBase Memory Extended MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device CPU Hyper-Threading Password CheckLimit Cpuid Max. to No-Execute Memory Protect NoteSPP Integrated PeripheralsUSB 2.0 Controller Onboard LAN Boot ROMUSB Keyboard Support USB Mouse SupportPower Management Setup Parallel Port ModeECP Mode Use DMA Resume by Alarm Power On by RingPower On By Mouse Power On By KeyboardPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status Frequency / Voltage Control CPU Smart FAN ModeCPU Smart FAN Control CPU Clock RatioCPU Host Frequency Mhz CPU Host Clock ControlPCI-E Frequency to CPU Memory Frequency ForFSB OverVoltage Control CPU Voltage ControlNormal CPU Vcore Load Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionXpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish 5 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device AMI Bios Beep Codes TroubleshootingEnglish English English English English Taiwan Headquarters Contact UsChina Shanghai