Intel GA-8I915MK-GV Frequency / Voltage Control, CPU Smart FAN Control, CPU Smart FAN Mode

Page 42

English

CPU Smart FAN Control

Disabled

Disable this function.

Enabled

When this function is enabled, CPU fan will run at different speed depending on

 

CPU temperature. Users can adjust the fan speed with Easy Tune based on

 

their requirements. (Default Value)

CPU Smart FAN Mode

This option is available only when CPU Smart FAN Control is enabled.

Auto

BIOS autodetects the type of CPU fan you installed and sets the optimal CPU

 

Smart FAN control mode for it. (Default Value)

Voltage

Set to Voltage when you use a CPU fan with a 3-pin fan power cable.

PWM

Set to PWM when you use a CPU fan with a 4-pin fan power cable.

Note: In fact, the Voltage option can be used for CPU fans with 3-pin or 4-pin power cables. However, some 4-pin CPU fan power cables are not designed following Intel 4-Wire fans PWM control specifications. With such CPU fans, selecting PWM will not effectively reduce the fan speed.

2-7

Frequency / Voltage Control

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

 

 

 

 

Frequency / Voltage Control

 

 

 

CPU Clock Ratio

[15X]

 

 

Item Help

 

CPU Host Clock Control

[Disabled]

 

Menu Level`

x CPU Host Frequency (Mhz)

133

 

 

 

x PCI-E Frequency to CPU

Auto

 

 

 

 

Memory Frequency For

[Auto]

 

 

 

 

Memory Frequency (Mhz)

333

 

 

 

 

DIMM OverVoltage Control

[Normal]

 

 

 

 

PCI-E OverVoltage Control

[Normal]

 

 

 

 

FSB OverVoltage Control

[Normal]

 

 

 

 

CPU Voltage Control

[Normal]

 

 

 

 

Normal CPU Vcore

1.3875V

 

 

 

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Safe Defaults

 

F7: Optimized Defaults

 

 

 

 

 

 

 

Incorrect using these features may cause your system broken. For power end-user use only.

CPU Clock Ratio

This setup option will automatically assign by CPU detection.

The option will display "Locked" and read only if the CPU ratio is not changeable.

GA-8I915MK-GV Motherboard

- 42 -

Image 42
Contents GA-8I915MK-GV Motherboard Copyright Product Manual ClassificationTable of Contents Install Drivers GA-8I915MK-GV Motherboard Layout 8I915MK-GVBlock Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Installation of Expansion Cards Dual Channel DDRI/O Back Panel Introduction Connectors Introduction EnglishATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 IDE Connector SATA0/SATA1 Serial ATA ConnectorFpanel Front Panel Connector Faudio Front Audio Panel Connector PwrledCdin CD in Connector Auxin AUX In ConnectorSpdifio Spdif In/ Out SurcenFUSB1 / FUSB2 Front USB Connectors Comb Comb ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosBAT Battery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F1 Standard Cmos Features IDE Channel 2/3 Master, Slave Floppy 3 Mode Support for Japan AreaIDE Channel 0 Master, Slave Drive a / Drive BBase Memory Halt onMemory Extended MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Limit Cpuid Max. to Password CheckCPU Hyper-Threading No-Execute Memory Protect NoteIntegrated Peripherals SPPUSB Keyboard Support Onboard LAN Boot ROMUSB 2.0 Controller USB Mouse SupportPower Management Setup Parallel Port ModeECP Mode Use DMA Power On By Mouse Power On by RingResume by Alarm Power On By KeyboardPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status CPU Smart FAN Control CPU Smart FAN ModeFrequency / Voltage Control CPU Clock RatioPCI-E Frequency to CPU CPU Host Clock ControlCPU Host Frequency Mhz Memory Frequency ForFSB OverVoltage Control CPU Voltage ControlNormal CPU Vcore Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Install Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewXpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Channel Audio Setup 5 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Troubleshooting AMI Bios Beep CodesEnglish English English English English Contact Us Taiwan HeadquartersChina Shanghai