Lenovo Q180 manual Enabling or disabling a device, Select Save changes and Exit from the menu

Page 21

1.Start the Setup Utility program (See ”Starting the Setup Utility program” on page 13.)

2.From the Security menu, select Set Power-On Password and press the Enter key.

3.The password dialog box will be displayed. Type the password, and press the Enter key.

4.Re-type the password to confirm, if you type the password correctly, the password will be installed.

To change a Power-On Password, do the following:

1.Start the Setup Utility program (See ”Starting the Setup Utility program” on page 13.)

2.From the Security menu, select Set Power-On Password and press the Enter key.

3.The password dialog box will be displayed. Type the current password then press the Enter key.

4.Type the new password, then press the Enter key. Re-type the password to confirm the new password, if you type the password correctly, the new password will be installed.

To delete a previously set Power-On Password, do the following :

1.From the Security menu, select Set Power-On Password and press the Enter key.

2.The password dialog box will be displayed. Type the current password and press the Enter key.

3.To delete the Power-On Password, Enter blank fields for each new password line item. A setup notice will display that changes have been saved.

4.Return to the Setup Utility program menu and select the Exit option.

5.Select Save changes and Exit from the menu.

Enabling or disabling a device

The Devices options is used to enable or disable user access to the following devices:

USB Functions

Select whether to enable or disable USB (Universal Serial

 

Bus) functions. If the functions are disabled, no USB

 

devices can be used.

 

 

SATA Controller

When feature is set to Disabled, all devices connected to

 

the SATA connectors (e.g. hard disk drives or the optical

 

disk drive) are disabled and can’t be accessed.

 

 

Onboard Audio Controller

Select whether to enable or disable the Onboard Audio

 

Controller, when feature is set to Disabled all devices

 

connected to the audio connectors (e.g. a headphone or

 

a microphone) are disabled and can’t be used.

 

 

Onboard Ethernet Controller or Onboard PXE

Select whether to enable or disable Onboard Ethernet

Controller

Controller, or select whether to enable or disable load

 

onboard PXE (Preboot Execution Environment).

 

 

To enable or disable a device, do the following:

1.Start the Setup Utility program (see “Starting the Setup Utility program” on page 13).

2.From the Setup Utility program menu, select Devices.

3.Select:

USB Setup press the Enter key, and then select USB Functions.

ATA Drives Setup press the Enter key , and then select SATA Mode.

Audio Setup press the Enter key, and then select Onboard Audio Controller.

Network Setup press the Enter key, then select Onboard Ethernet Support or LAN Boot Agent. 4. Select Disabled or Enabled and press the Enter key.

Chapter 5. Using the Setup Utility 15

Page 20 Page 22
Image 21
Page 20 Page 22
Contents IdeaCentre Q180 Hardware Maintenance Manual Page IdeaCentre Q180 Hardware Maintenance Manual Page Contents Iv IdeaCentre Q180Hardware Maintenance Manual About this manual Important Safety InformationIdeaCentre Q180Hardware Maintenance Manual Safety information General safetyElectrical safety IdeaCentre Q180Hardware Maintenance Manual Handling electrostatic discharge-sensitive devices Safety inspection guideGrounding requirements Safety noticesTo Connect To Disconnect Do not≥18 kg37 lbs ≥32 kg70.5 lbs ≥55 kg121.2 lbs General information SpecificationsType IdeaCentre Q180 EnvironmentIdeaCentre Q180Hardware Maintenance Manual General Checkout IdeaCentre Q180Hardware Maintenance Manual Starting the Setup Utility program Using the Setup UtilityViewing and changing settings Using passwordsAdministrator Password Setting, changing, or deleting an Administrator passwordSetting, changing, or deleting a Power-On Password Select Save changes and Exit from the menu Enabling or disabling a deviceSelecting a startup device Exiting the Setup Utility programSelecting a temporary startup device Selecting or changing the startup device sequenceUsing the Setup Utility IdeaCentre Q180Hardware Maintenance Manual Hard disk drive boot error Symptom-to-FRU IndexPower Supply Problems Error FRU/ActionPost error codes Undetermined problemsPost Error Message Description/Action Locating components, controls and connectors LocationsFront view Rear view Hardware components Identifying parts on the motherboard Pre-disassembly instructions Replacing hardwareGeneral information To replace the optical drive Replacing the optical driveTo remove the computer cover Removing the computer coverTo replace the hard disk drive Replacing the hard disk driveTo replace a memory module Replacing a memory moduleTo remove the power button Removing the power buttonReplacing the Wlan card To replace the Wlan cardTo replace the CPU heatsink and system fan Replacing the CPU heatsink and system fanTo replace the motherboard Replacing the motherboardTo replace the keyboard and mouse Replacing the keyboard and mouseFRU lists Item # FRUsComputer Cover Q180 TOP case module 110200358 Wlan card Hard disk drivesMemory module MotherboardPower button ChassisSystem fan and heatsink Power management Additional Service InformationAdvanced configuration and power interface Acpi Bios Automatic Power-On features
Top Page Image Contents