Lenovo 9212, 9213 manual Plugs and outlets, Batteries

Page 10

product. Never overload these devices. If power strips are used, the load should not exceed the power strip input rating. Consult an electrician for more information if you have questions about power loads, power requirements, and input ratings.

Plugs and outlets

If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damaged or corroded, do not use the outlet until it is replaced by a qualified electrician.

Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a replacement.

Some products are equipped with a three-pronged plug. This plug fits only into a grounded electrical outlet. This is a safety feature. Do not defeat this safety feature by trying to insert it into a non-grounded outlet. If you cannot insert the plug into the outlet, contact an electrician for an approved outlet adapter or to replace the outlet with one that enables this safety feature. Never overload an electrical outlet. The overall system load should not exceed 80 percent of the branch circuit rating. Consult an electrician for more information if you have questions about power loads and branch circuit ratings.

Be sure that the power outlet you are using is properly wired, easily accessible, and located close to the equipment. Do not fully extend power cords in a way that will stress the cords.

Carefully connect and disconnect the equipment from the electrical outlet.

Batteries

All personal computers manufactured by Lenovo contain a non-rechargeable coin cell battery to provide power to the system clock. In addition many mobile products such as ThinkPad notebook PCs utilize a rechargeable battery pack to provide system power when in portable mode. Batteries supplied by Lenovo for use with your product have been tested for compatibility and should only be replaced with approved parts.

Never attempt to open or service any battery. Do not crush, puncture, or incinerate batteries or short circuit the metal contacts. Do not expose the battery to water or other liquids. Only recharge the battery pack strictly according to instructions included in the product documentation.

Battery abuse or mishandling can cause the battery to overheat, which can cause gasses or flame to “vent” from the battery pack or coin cell. If your battery is damaged, or if you notice any discharge from your battery or the buildup of foreign materials on the battery leads, stop using the battery and obtain a replacement from the battery manufacturer.

Batteries can degrade when they are left unused for long periods of time. For some rechargeable batteries (particularly Lithium Ion batteries), leaving a battery unused in a discharged state could increase the risk of a battery short circuit, which could shorten the life of the battery and can also pose a safety hazard. Do not let rechargeable Lithium-Ion batteries completely discharge or store these batteries in a discharged state.

viiiUser Guide

Page 9 Page 11
Image 10
Page 9 Page 11
Contents User Guide Types 9212 Page User Guide Types 9212 Page Contents Iv User Guide Important safety information Conditions that require immediate actionGeneral safety guidelines ServicePower cords and power adapters Extension cords and related devicesPlugs and outlets BatteriesCD and DVD drive safety Heat and product ventilationLithium battery notice Additional safety informationTo connect To disconnect Modem safety information Laser compliance statementPower supply statement Overview Information resourcesXiv User Guide Installing options FeaturesMemory Operating systems, preinstalled varies by model type Available options Specifications Tools requiredInstalling external options Handling static-sensitive devicesLocating the connectors on the front of your computer Locating the connectors on the rear of your computer Connector Description Obtaining device driversRemoving the cover Locating components Identifying parts on the system boardInstalling memory modules Installing adapters What to do nextWhat to do next Installing internal drives Drive specificationsUser Guide Installing a drive in bay 1 or bay Installing a hard disk drive in bay Installing options Connecting drives Connecting the first optical driveConnecting a serial ATA hard disk drive Installing security featuresChanging the battery Password protectionPadlock Erasing a lost or forgotten password clearing Cmos Replacing the cover and connecting the cables Using the Setup Utility program Using Security Profile by Device Setting, changing, and deleting a passwordSelecting a startup device Selecting a temporary startup device Exiting from the Setup Utility programChanging the startup sequence User Guide Appendix A. Updating system programs Updating flashing Bios from a diskette or CD-ROMUpdating flashing Bios from your operating system System programsRecovering from a POST/BIOS update failure Cleaning an optical mouse Appendix B. Cleaning the mouseCleaning a mouse with a ball User Guide Appendix C. Manual modem commands Basic AT commandsSet Tone Dial as default Low speaker volumeSet Pulse dial as default Internal speaker on until carrier detectedExtended AT commands MNP/V.42/V.42bis/V.44 commands Fax Class 1 commands Fax Class 2 commandsVoice commands Appendix C. Manual modem commands User Guide Appendix D. Notices Television output notice TrademarksIndex Sata connectors Page Part Number 39J7678
Top Page Image Contents