Lenovo TS140 manual Removing the tertiary hard disk drive, What to do next

Page 60

9.Connect the cable of the fan for the tertiary hard disk drive to one of the available connectors 1 of the fan power converter cable. Then, connect the connector 2 to the hard disk drive fan connector on the system board. See “Locating parts on the system board” on page 15.

Figure 19. Connecting the cable of the fan for the tertiary hard disk drive

10.Remove the plastic panel that protects the secondary optical drive bay from the front bezel.

11.Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 38.

What to do next:

•To work with another piece of hardware, go to the appropriate section.

•To complete the installation, go to “Completing the parts replacement” on page 79.

Removing the tertiary hard disk drive

Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 35.

This topic provides instructions on how to remove the tertiary 3.5-inch hard disk drive.

To remove the tertiary 3.5-inch hard disk drive, do the following:

1.Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server.

2.Remove the server cover. See “Removing the server cover” on page 37.

3.Remove the front bezel. See “Removing and reinstalling the front bezel” on page 38.

4.Disconnect the signal cable and the power cable from the rear of the tertiary hard disk drive.

5.Disconnect the cable of the fan for the tertiary hard disk drive from the fan power converter cable.

48ThinkServer TS140 User Guide

Image 60

Contents ThinkServer TS140 User Guide First Edition September Copyright Lenovo Contents Index Safety information 제품을 사용하기 전에 제품과 함께 제공되는 문서 DVD의 다국어 안전 지침을 주의 깊게 읽어보십시오在使用本产品之前，请务必先阅读和了解产品附带的文档 DVD 中的多语言安全说明。 Statement ≥ 18 kg 39.7 lb ≥ 32 kg 70.5 lb ≥ 55 kg 121.2 lb Vii Statement Following label indicates a potential heat hazard Copyright Lenovo ThinkServer TS140 User Guide General information IntroductionServer documentation Printed documentDocumentation DVD Safety, Warranty, and Support Information Document only for trained service personnelThinkServer TS140 User Guide Server setup road map ThinkServer TS140 User Guide Features Product overviewServer package MicroprocessorPower supply Input/Output I/O featuresMemory FansReliability, availability, and serviceability Security featuresBasic system management features Ethernet connectivitySpecifications SoftwareThinkServer EasyStartup ThinkServer EasyUpdate Firmware Updater Bios update utilitiesRAID configuration utilities Diagnostic programsFront view of the server Machine type, model, and serial number labelRear view of the server Following illustration shows the front view of the serverConnector Connector Description Locating parts on the system boardInternal components Internal drivesDrive bay locations ThinkServer TS140 User Guide Turning on and turning off the server Turning on the serverTurning off the server ThinkServer TS140 User Guide Configuring the server Using the Setup Utility programStarting the Setup Utility program Viewing information in the Setup Utility programSetup Utility program interface Main menuDevices menu Advanced menu Security menuSetting the system date and time Power menuStartup menu Exit menuUsing passwords Configuring the TPM function Selecting a startup deviceExiting from the Setup Utility program Updating or recovering the BiosUpdating flashing the Bios Using the ThinkServer EasyStartup program Recovering from a Bios update failureFeatures of the ThinkServer EasyStartup program Starting the ThinkServer EasyStartup programInstall operating system HomeCompatibility notes User GuideConfiguring RAID About RAIDSelect Devices ATA Drive Setup Creating RAID volumes Deleting RAID volumesResetting disks to non-RAID Using the Firmware Updater program Updating the firmwareInstalling, removing, or replacing hardware PrecautionsGuidelines Handling static-sensitive devices Working inside the server with the power on System reliability guidelinesRemoving the server cover Removing and reinstalling the front bezel Removing the server coverRemoving the front bezel Installing, removing, or replacing hardware What to do nextInstalling or removing the Ethernet card Installing or removing a memory moduleMemory module installation rules Dimm DIMM1 DIMM2 DIMM3 DIMM4 Installing a memory module Opening the retaining clips of the memory slotsInstalling a memory module Removing a memory moduleInstalling or removing the tertiary hard disk drive Installing the tertiary hard disk driveInstall the retainer on the side of the bracket Connecting cables to the hard disk drive Removing the tertiary hard disk drive Removing the drive conversion bracket Installing the slim optical drive conversion board Installing the slim optical drive retainer Install the cage retainer on the side of the cage Sliding the cage into the optical drive bay What to do next Removing the slim optical drive from the cage Installing or replacing a PCI card Removing the hard disk drive from the cageOpening the PCI card latch Opening the PCI card retaining clip Installing a PCI card Installing or replacing the optical drive Removing the optical driveInstalling or replacing the secondary hard disk drive Installing the optical driveRemoving the secondary hard disk drive Installing the hard disk drive into the bracket Connecting a Sata hard disk drive Replacing the primary hard disk driveRemoving the primary hard disk drive Replacing the power supply assembly Installing the primary hard disk driveInstalling, removing, or replacing hardware Removing the screws that secure the power supply assembly Replacing the heat sink and fan assembly Removing the heat sink and fan assembly Replacing the front audio and USB assembly Removing the front audio and USB assemblyReplacing the front fan assembly Removing the front fan assemblyReplacing the rear fan assembly Installing the front fan assemblyRemoving the rear fan assembly Installing the rear fan assembly Replacing the microprocessorAccessing the microprocessor Installing the microprocessor Replacing the system board battery Completing the parts replacement Removing the old system board batteryConnecting the cables Reinstalling the server coverConnecting external devices Updating the server configurationInstalling security features Password protectionThinkServer TS140 User Guide Troubleshooting and diagnostics Troubleshooting procedureUsing a diagnostic program Basic troubleshooting tables ThinkServer EasyStartup program problemsOptical drive problems Hard disk drive problems Memory module problems Keyboard, mouse, or USB device problems Restart the server Replace the USB device Getting information, help, and service Using the documentationInformation resources ThinkServer Web siteHelp and service Calling for serviceBefore you call Using other services Purchasing additional servicesThinkServer TS140 User Guide Appendix A. Notices Trademarks Important notesParticulate contamination Battery return program Contaminant LimitsBattery recycling information for the European Union Important Weee information Restriction of Hazardous Substances Directive RoHSChina RoHS Turkish RoHS India RoHS European Union RoHSGerman Ordinance for Work gloss statement Export classification noticeUnited Kingdom telecommunications safety requirement Industry Canada Class a emission compliance statementDeutschland Appendix A. Notices Eurasian compliance mark Energy Star model information Index 103RAID 105 ThinkServer TS140 User Guide