Lenovo 1098, 1105, 1100 German Ordinance for Work gloss statement, Electronic emission notices

Page 104

German Ordinance for Work gloss statement

The product is not suitable for use with visual display work place devices according to clause 2 of the German Ordinance for Work with Visual Display Units.

Das Produkt ist nicht für den Einsatz an Bildschirmarbeitsplätzen im Sinne § 2 der Bildschirmarbeitsverordnung geeignet.

Electronic emission notices

This topic includes electronic emission notices.

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult an authorized dealer or service representative for help.

Lenovo is not responsible for any radio or television interference caused by using other than specified or recommended cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Industry Canada Class B emission compliance statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

European Union - Compliance to the Electromagnetic Compatibility Directive

This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Lenovo cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the installation of option cards from other manufacturers.

92ThinkServer User Guide

Page 103 Page 105
Image 104
Page 103 Page 105
Contents ThinkServer User Guide First Edition May Copyright Lenovo Contents Information resources Safety information IiiStatement Do not ≥ 18 kg 39.7 lb ≥ 32 kg 70.5 lb ≥ 55 kg 121.2 lb Vii Viii ThinkServer User Guide Copyright Lenovo ThinkServer User Guide General information IntroductionRelated documentation Server setup road map Task Where to find the informationThinkServer User Guide Product overview What is included with your serverFeatures and specifications System management features Input/Output I/O featuresPreinstalled operating system MemoryEasyStartup Reliability, availability, and serviceabilitySoftware programs ThinkServer User Guide Rear view Locating parts, controls, and connectorsFront view Connector Description Locating parts on the system board System board part locationsInternal components Component locationsInternal drives Machine type and model labelFollowing is a sample of the machine type and model label Basic guidelines Installing, removing, or replacing hardwareGuidelines System reliability guidelines Handling static-sensitive devicesRemoving the server cover Removing and reinstalling the front bezel Removing the server coverRemoving the front bezel Installing, removing, or replacing optional hardware devices Installing or replacing a PCI cardOpening the PCI card latch Removing a PCI card Installing or removing the Ethernet card Installing a PCI cardInstalling or removing a memory module Removing a memory module Installing or replacing the optical drive Installing a memory moduleRemoving the optical drive Connecting a Sata optical drive Replacing the primary hard disk driveRemoving the primary hard disk drive Installing the primary hard disk drive Installing or replacing the secondary hard disk drive Connecting a Sata hard disk driveRemoving the secondary hard disk drive Installing the secondary hard disk drive Installing, removing, or replacing hardware devices Replacing the power supply assembly Removing the screws that secure the power supply assembly Replacing the heat sink and fan assembly Removing the heat sink and fan assembly Replacing the front audio and USB assembly Removing the front audio and USB assemblyReplacing the front fan assembly Removing the front fan assembly Replacing the rear fan assembly Installing the front fan assemblyRemoving the rear fan assembly Installing the rear fan assembly Replacing the microprocessorAccessing the microprocessor Installing the microprocessor Replacing the system board battery Completing the parts replacement Removing the old system board batteryConnecting the cables Turning on the serverConnecting external devices Turning off the serverUpdating the server configuration Installing security featuresPassword protection Integrated cable lockThinkServer User Guide Configuring the server Using the Setup Utility programStarting the Setup Utility program Introduction of the Bios itemsOption or description UuidIGD/PEG/PCI Option DescriptionSubmenus under the Serial Port Setup menu Submenus under the Video Setup menu Submenus under the Network Setup menu CPU ID Under the SOL Configuration menu VT-UTF8 AsciiUnder the Automatic Power On LANItems under the Security menu Under the Hard Disk Password Under the Fingerprint Setup menuUnder the TCG Feature Setup Under the System Event Log menuSubmenus under the Fingerprint Setup menu Items under the Startup menu Viewing and changing settings Using passwordsPassword considerations USB Setup Enabling or disabling a deviceSata Controller External Sata PortExiting from the Setup Utility program Configuring RAIDSelecting a startup device RAID levelCreating RAID volumes Deleting RAID volumesUpdating the firmware Resetting disks to non-RAIDUsing the EasyUpdate Firmware Updater program Updating system programs Using the ThinkServer EasyStartup programUsing system programs Updating flashing the Bios from a disc Updating flashing the Bios from your operating systemRecovering from a POST/BIOS update failure Troubleshooting and diagnostics Basic troubleshootingGeneral problems Symptom ActionRunning the diagnostic program from a diagnostic disc EasyStartup problemsPC-Doctor for DOS Creating a diagnostic disc Troubleshooting and diagnostics ThinkServer User Guide Lenovo Support Web site Safety and WarrantyInformation resources ThinkServer User Guide Calling for service Help and serviceUsing the documentation Using other services Purchasing additional servicesAppendix A. Notices Trademarks Appendix A. Notices Important information for the European Directive 2002/96/EC Appendix A. Notices ThinkServer User Guide Particulate contamination Restriction of Hazardous Substances Directive RoHS Contaminant LimitsChina RoHS Turkish statement of compliance Federal Communications Commission FCC Statement German Ordinance for Work gloss statementElectronic emission notices Appendix A. Notices ThinkServer User Guide Index CRUAdministrator Considerations Server configuration ThinkServer User Guide
Top Page Image Contents