Sanyo PLC-SU60, PLC-XU60 owner manual Appendix, Troubleshooting

Page 47

Appendix

Troubleshooting

Before calling your dealer or service center for assistance, check the items below once again.

–Make sure you have properly connected the projector to peripheral equipment as described in "Connecting to a Computer" and “Connecting to Video Equipment” on page17 and 18.

–Make sure all equipment is connected to AC outlet and the power is turned on.

–When you operate the projector with a computer and it does not project an image, restart the computer.

Problem:

No power

Image is out of focus.

No image

No sound

Image is Left/Right reversed.

Image is Top/Bottom reversed.

Some displays are not seen during the Operation.

–Try these solutions.

–Plug the power cord of the projector into the AC outlet.

–See if the POWER indicator lights red.

–Wait 90 seconds after the projector is turned OFF when turning the projector back on. The projector can be turned on after the POWER indicator turns red. (See “Turning Off the Projector” on page 19.)

–Check the WARNING indicator. If the WARNING indicator lights red, the projector cannot be turned on. (See "Warning Indicator" on page 43.)

–Check the projection lamp. (See page 45.)

–Unlock Key lock for the projector in the Setting Menu. (See page 42.)

–Adjust focus of the projector.

–Provide proper distance between the projector and the projection screen. (See page 16.)

–Check the projection lens to see if it needs cleaning. (See page 44.)

–Moving the projector from a cool temperature location to a warm temperature location may result in moisture condensation on the projection lens. In such an event, leave the projector OFF and wait until condensation disappears.

–Check the connection between your computer or video equipment and the projector.

–See if the input signal is correctly output from your computer. Some laptop computers may need changing the setting for monitor output when you are connecting a laptop computer. See your computer’s owner’s manual for setting.

–It takes about 30 seconds to display an image after turning on the projector.

–See if the selected system is corresponding with your computer or video equipment.

–Select correct input source once again through menu operation.

–Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C).

–Check audio cable connection from audio input source.

–Adjust the audio source.

–Press the Volume (+) button.

–Press the Mute button.

–Check the Ceiling / Rear item. (See “Setting” on page 40.)

–Check the Ceiling item. (See “Setting” on page 40.)

–Check the Display item. (See “Setting” on page 39.)

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Model PLC-XU60 PLC-SU60 Table of Contents Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsMoving the Projector Safety InstructionsInstalling the Projector in Proper Position Air CirculationFederal Communication Commission Notice Compliance200 240 V AC ComplianceFor Continental Europe For the U.K For the U.S.A. and CanadaFeatures and Design Front Back Bottom Part Names and FunctionsTerminal Part Names and Functions1!2 TopZoom Freeze Remote ControlPointer Function Laser Pointer FunctionWireless Mouse Operation Remote Control CodeRemote Control Batteries Installation Remote Control Operating RangePositioning the Projector InstallationAdjustable Feet Terminals Projector InstallationConnecting to a Computer Video Source example Connecting to Video EquipmentTurning Off the Projector Basic OperationTurning On the Projector Basic Operation Zoom AdjustmentFocus Adjustment Keystone AdjustmentKeystone correction Corner Auto Set Up FunctionPicture Freeze Function Direct Operation Timer FunctionSound Adjustment No Show FunctionOn-Screen Menu Remote ControlOn-Screen Menu Top ControlMenu Bar Input Source Selection Computer InputMode Computer InputComputer System Selection AutoAuto PC Adj Computer Adjustment AutoTo store adjustment data Computer Adjustment Manual To clear adjustment data ResetMode free Display area To store adjustment dataImage button Standard Real Image Level SelectionStandard RealImage Level Adjustment Screen Size Adjustment Pb/Cb, Pr/Cr Video InputInput Source Selection Video, S-Video, Y, Pb/Cb, Pr/Cr Input button Computer Video Computer 2 button Video InputInput Source Selection RGB Scart 21-Pin RGB ScartAV System Menu Video or S-Video Video System SelectionVideo or S-Video ComponentImage button Standard Cinema CinemaProgressive ColorTint Resets all adjustment to their previous figure Setting SettingSetting Pointer Power managementLamp mode On startTo change the code for the projector To change the code for the remote controlWireless Mouse mode Projector modeThen check the items below Maintenance and CleaningProjector is shut down and the Warning indicator lights red Cleaning the Projector Cabinet Maintenance and CleaningCleaning the Air Filters Cleaning the Projection LensReset the Lamp replace counter Lamp ReplacementLamp Replace Counter Lamp Handling PrecautionsAppendix TroubleshootingAppendix Projector Condition Indicators and Projector ConditionInput PC AdjustImage Adjust Screen Menu TreeSound System SettingImage Adjust Image SelectKHz Compatible Computer SpecificationsFreq Technical Specifications Terminal DVI-I Pin Configuration Configurations of TerminalsTerminal HDB15-PIN Pin Configuration Optional Parts Attaching the Lens Cover Off Projector is not locked with USB Key On1 Key registrationDeleting key registration To lock the projector with USB keyAppendix Appendix Part No 312 4803 1AA6P1P4451-- MF7AA

PLC-XU60, PLC-SU60 specifications

The Sanyo PLC-SU60 and PLC-XU60 are projectors that embody cutting-edge technology and innovative features, catering to a variety of presentation needs in educational and corporate environments.

The PLC-SU60, a high-performance model, boasts a native resolution of 1024 x 768 pixels, providing clear and crisp images. It utilizes a 3LCD system, which enhances color accuracy and brightness. With a brightness of 6000 lumens, this projector is particularly well-suited for large venues with ambient light, ensuring that presentations remain vibrant and legible even in well-lit rooms. The model also incorporates advanced lens shift and zoom capabilities, allowing for flexible installation options without compromising image quality.

On the other hand, the PLC-XU60 targets a similar audience but emphasizes portability alongside performance. This projector features a native XGA resolution with a brightness of 5000 lumens. It, too, utilizes the 3LCD technology, ensuring bright and colorful images. The lightweight design of the PLC-XU60 makes it an ideal choice for on-the-go presenters who need a reliable device that can easily transition from one location to another.

Both models are equipped with multiple connectivity options, including HDMI, VGA, and component inputs, which make them compatible with a wide array of devices from laptops to Blu-ray players. The easy-to-navigate user interface simplifies operation, providing users with instant access to settings suitable for different environments.

A noteworthy characteristic of Sanyo projectors is their commitment to minimizing noise during operation. The PLC-SU60 and PLC-XU60 operate at whisper-quiet levels, allowing for uninterrupted presentations. Additionally, both projectors come with a long lamp life, which reduces maintenance costs and extends usage time.

In summary, the Sanyo PLC-SU60 and PLC-XU60 are designed for those who need reliable, high-quality projection solutions. With their impressive brightness, outstanding color accuracy, and versatile connectivity, these projectors cater to the diverse requirements of modern-day presentations. Whether in an educational setting or a business environment, these models ensure that visuals are portrayed vividly and effectively, reinforcing the importance of investing in robust projection technology.
Top Page Image Contents