Sanyo PLC-XE34 owner manual Standby mode, Timer

Page 51

Setting

Standby mode

This function is available when operating the projector via network.

Network..... Supply the power to the network function even

after turning off the projector by pressing the ON/STAND-BY button on the remote control. You can turn on/off the projector via network, modify network environment, and receive an e-mail about projector status while the projector is powered off.

Eco............. Select Eco when you do not use the projector

via network. The projector’s network function will stop when turning off the projector, you can not turn on the projector via network.

Refer to the owner’s manual of “Network Set-up and Operation”.

✔Note:

•When selecting Network, the cooling fans may be running depending on the temperature inside the projector even if the projector is turned off.

•When Eco mode is selected and the projector is in Stand- by, the communication of RS-232C serial port is not available.

P-timer

This function allows you to change the setting of the P-timer and execute it.

Select one of the following options:

Count up

The P-timer display 000:00 appears on the

Count down

screen and the count starts (000:00–180:00)

The time set in the Timer setting appears on

 

the screen and the countdown starts.

Timer

Use the Point ▲▼ buttons to set the Timer

 

(1–180 Min). Timer is available in Count

Start

down only. Factory default velue is 10 Min.

It executes the count up or count down

 

function. Press the SELECT button at

 

Start and the indication changes into

 

Stop. To stop Count up or Count down,

 

press the SELECT button at Stop on the

 

screen menu,then the indication changes

 

into Restart. Press the SELECT button

 

at Restart to resume Count up or Count

Reset

down.

Reset the P-timer values.

 

Press the SELECT button at Reset to return

 

to the following value;

 

Count up ... "000:00"

Exit

Count down ... Timer that you set

To exit the P-timer operation.

P-TIMER

0

P-timer display

Start

Reset

Exit

Stop or Cancel the P-timer via Remote Control To stop the P-timer, press the P-TIMER button.

To cancel the P-timer, press and hold the P-TIMER button for a few seconds.

51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Network Supported Model PLC-XE34Features and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Safety Instructions Air Circulation Installing the Projector in Proper PositionMoving the Projector AC Power Cord for the United States and Canada AC Power Cord for the United KingdomCompliance Bottom Part Names and FunctionsFront Back⑥ LAN Connection Terminal ⑦ Audio IN（Video Part Names and Functions Rear TerminalPart Names and Functions Top Control Part Names and Functions Remote Control Remote Control Operating Range Remote Control CodeTwo AAA size batteries Installation Adjustable FootPositioning the Projector Cables used for connection Installation Connecting to a ComputerInstallation Connecting to Video Equipment Audio OUT For the U..S..A.. and Canada Installation Connecting the AC Power CordProjector side AC outlet side For Continental Europe For the U..KSelected Input Source and Lamp Control Input signal guidance windowBasic Operation Turning On the ProjectorPIN Code Input Dialog Box Basic OperationDirect OFF Function Basic Operation Turning Off the ProjectorOn-Screen Menu Basic Operation How to Operate the On-Screen MenuRemote Control Top Control① Input ④ Image adjust⑦ Setting Basic Operation Menu BarBasic Operation Zoom and Focus Adjustment Auto Setup FunctionKeystone Correction Mute Basic Operation Sound AdjustmentVolume Volume Dialog BoxBasic Operation Remote Control Operation Screen button Timer buttonNo Show button Image buttonComputer Input Input Source Selection RGB Computer 1/ComputerInput Menu Mode Computer Input Computer System SelectionPC System Menu AutoAuto PC adj Computer Input Auto PC AdjustmentPC adjust Menu To store adjustment parametersComputer Input Manual PC Adjustment Computer Input ResetMode free Mode freeImage select Menu Computer Input Image Mode SelectionImage Adjust Menu Computer Input Image AdjustmentScreen Menu Screen Size AdjustmentDigital zoom Custom adjPosition H/V Digital zoom +Input Menu Video InputInput Source Selection Video, S-video VideoRGB Scart ComponentSelect Video , S-video or Computer 1Component Video Input Video System SelectionVideo or S-video Component AV System Menu ComponentDynamic Standard Cinema Blackboard Green Colorboard Image Video Input Image Mode SelectionCinema Image buttonVideo Input Image Adjustment ColorTint Noise reduction Off Disabled Lower reduction Higher reduction ProgressiveVideo Input Store MenuVideo Input Screen Size Adjustment Language SettingSetting Setting Menu LanguageAuto Keystone Auto setupAuto setup Input searchDisplay Power off? p.20Keystone BackgroundLogo select Logo Logo and Logo PIN code lock settingsDefault Logo selectLogo PIN code lock CaptureLogo PIN code lock CaptureChange the Logo PIN code lock setting Enter a Logo PIN codeChange the Logo PIN code Computer CeilingRear TerminalPower management Shut downDirect on Timer Standby modeClosed Caption Lamp control Lamp control Remote controlRemote control To change the code for the remote controlPIN code lock Key lock PIN code lockSecurity Key lock and PIN code lock Key lockEnter a PIN code Change the PIN code Change the PIN code lock settingFan control Lamp counter resetVideo delay control FanFilter counter Factory defaultFactory default Filter counterInput Source Information Display InformationMaintenance and Cleaning Projector is shut down and the Warning indicator lights redThen check the matters below Maintenance and Cleaning Cleaning the Filters Resetting the Filter CounterFilter counter Maintenance and Cleaning Attaching the Lens Cap Cleaning the Projection LensCleaning the Projector Cabinet Lamp Replace indicator Maintenance and Cleaning Lamp ReplacementReset the lamp replacement counter Lamp replacement iconService Parts No 349 Maintenance and CleaningAppendix TroubleshootingAppendix PIN code dialog box appears Remote Control doesIndicator blinks or lights Image is distorted or runs offAppendix Appendix Menu Tree System AutoSetting Image select Image Adjust ScreenInformation Indicators Appendix Indicators and Projector ConditionON-SCREEN Resolution Appendix Compatible Computer SpecificationsAppendix Technical Specifications Optional Parts Appendix PJ Link Notice Appendix Configurations of Terminals Control Port Connector D-sub 9 pinTerminal Analog RGB Mini D-sub 15 pin Appendix PIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Dimensions Appendix KJ2AC

PLC-XE34 specifications

The Sanyo PLC-XE34 is a compact and versatile LCD projector designed to meet the needs of various applications, from educational settings to business presentations. Known for its portability and robust performance, it offers a range of features that cater to users who require reliability and quality.

One of the standout features of the PLC-XE34 is its brightness capability, producing an impressive output of 3000 ANSI lumens. This level of brightness ensures that presentations and videos maintain high visibility, even in well-lit environments. The projector's 1024 x 768 XGA resolution provides clarity and sharpness, making it suitable for detailed graphics and text. This resolution strikes a balance between performance and image quality, appealing to educators and professionals alike.

The PLC-XE34 also incorporates advanced LCD technology that enhances color performance and reduces the occurrence of artifacts. With a contrast ratio of 500:1, it produces vibrant colors and deep blacks, which is essential for engaging presentations. The projector's ability to handle a wide color spectrum ensures that images are both accurate and visually appealing.

In terms of connectivity, the projector is equipped with multiple input options, including HDMI, VGA, and composite video, allowing it to connect seamlessly to various devices such as laptops, DVD players, and tablets. The inclusion of a built-in URL function simplifies the process of displaying content from the internet, catering to modern presentations that often require web access.

Portability is another flagship characteristic of the Sanyo PLC-XE34. Weighing in at just a few kilograms, it is easy to transport between locations, making it ideal for mobile professionals and educators who need to set up quickly. The user-friendly interface and remote control functionality enhance the convenience of operation, allowing users to navigate menus and settings effortlessly.

Furthermore, the PLC-XE34 boasts a long lamp life, reaching up to 4000 hours in eco-mode. This longevity reduces maintenance costs and the frequency of replacements, providing users with a cost-effective solution over time. The projector’s efficient cooling system also contributes to its reliability during extended use.

In summary, the Sanyo PLC-XE34 is a powerful and flexible projector that integrates effective brightness, advanced LCD technology, and a range of connectivity options into a portable design. Its combination of high-performance features and user-friendly operation makes it a compelling choice for anyone in need of a dependable projection solution. Whether for classroom use, business meetings, or casual presentations, the PLC-XE34 stands out as a noteworthy option.
Top Page Image Contents