Sanyo PLC-XL50 owner manual Maintenance and Cleaning Lamp Replacement, Reset the lamp counter

Page 62
Connect the AC power cord to the projector and turn on the projector.
Turn off the projector and unplug the AC power cord. Let the projector cool for at least 45 minutes.
Remove the screw from the lamp cover and open the cover.
Loosen the two (2) screws that secure the lamp. Lift the lamp out of the projector by using the handle.

Maintenance and Cleaning

Lamp Replacement

When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP REPLACE indicator should light is depending on the lamp mode.

WARNING:

TURN OFF THE UV LAMP BEFORE 

OPENING THE LAMP COVER

Note:

•The Lamp replacement icon will not appear when the Display function is set to “Off” (p.46), during “Freeze” (p.25), or “No show” (p.26).

Indicators

LAMP REPLACE

indicator

 

Lamp replacement icon

CAUTION

Allow a projector to cool for at least 45 minutes before you open the Lamp cover. The inside of the projector can become very hot.

CAUTION

For continued safety, replace with a lamp of the same type. Do not drop a lamp or touch a glass bulb! The glass can shatter and may cause injury.

Follow these steps to replace the lamp.

1

2

3

4 Replace the lamp with a new one and secure the two

(2)screws. Make sure that the lamp is set properly. Close the lamp cover and secure the screw.

5

6 Reset the lamp counter.

See “Lamp Replacement Counter” on the next page.

Note:

•When replacing the projection lamp, protect the infrared remote receiver with a soft cloth to avoid damaging it.

Lamp Cover

Screw

Screw Handle

Screw

Lamp

ORDER REPLACEMENT LAMP

Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer.

Model No. of your projector

: PLC-XL50

Replacement Lamp Type No.

: POA-LMP121

 

 

(Service Parts No. 610 337 9937)

62

Image 62
Contents Model PLC-XL50 Features and Design Large Screen in Limited SpaceTable of Contents Safety Precaution To the OwnerSafety Instructions Safety Instructions Air Circulation Moving the ProjectorSide a Side B Side C Side D Side ECompliance Federal Communications Commission NoticeFront Back Top controls and Indicators e Exhaust VentPart Names and Functions BottomPart Names and Functions Rear Terminal Part Names and Functions Top Part Names and Functions Remote Control Part Names and Functions Remote Control Battery Installation Operating RangePositioning the Projector InstallationAdjustable Feet Stand Installation Mounting the Rear Leg and the StandRear Leg Installation Connecting to Computer Cables used for connectionInstallation Connecting to Video Equipment Video, S-Video Computer Component Audio Installation Connecting the AC Power Cord Projector side AC outlet sideTurning On the Projector What is PIN code?Basic Operation Enter a PIN codeBasic Operation Turning Off the Projector Top Control Basic Operation How to Operate the On-Screen MenuRemote Control Select button On-Screen Menu Menu button Point buttonsFor video source Basic Operation Menu BarFor computer source Focus Adjustment Basic Operation Zoom AdjustmentScreen Position Adjustment Remote ControlCOMPUTER/VIDEO button Basic Operation Sound AdjustmentRemote Control Operation Freeze buttonBasic Operation Input Menu Computer InputInput Source Selection Source Select MenuPC System Menu Computer Input Computer System SelectionAuto ModeTo store the adjusted parameters Computer Input Auto PC AdjustmentDirect Operation Remote Control PC Adjust MenuComputer Input Manual PC Adjustment Computer Input Computer Input Image Level Selection BlackboardGreen Image Select MenuComputer Input Image Level Adjustment Screen Size Adjustment Digital zoom For zooming in and out the imagesDigital zoom + Auto Video Component Video InputInput Source Selection Video, S-Video, Component Video Input Input Source Selection RGB Scart 21-pin RGB ScartComponent Auto Video Input Video System SelectionVideo or S-Video Auto AV System Menu Video or S-VideoVideo Input Image Level Selection CinemaVideo Input Image1-4Tint Video Input Image Level AdjustmentColor Noise reduction ProgressiveVideo Input Screen Size Adjustment Language Setting Menu Language SettingSetting ZoomDisplay Uniformity adjBlue back Capture Logo Logo and Logo PIN code lock settingsLogo select Logo select CaptureLogo PIN code lock Enter a Logo PIN codeChange the Logo PIN code Terminal CeilingRear Input searchLamp control Power managementOn start To change the code for the projector Security Key lock, PIN code lock, Alarm settingsRemote control Key lock Key lockPIN code lock Enter a PIN codeChange the PIN code Change the PIN code lock settingChange the PIN code lock setting Change the PIN codeFan Factory defaultLamp Replacement icon Lamp counterSet and release the Antitheft alarm function Antitheft Alarm FunctionHow to Use the Antitheft Alarm Function IndicatorAntitheft Alarm Function Other settingsReplace the rechargeable batteries How to replace the rechargeable batteriesCharge the built-in batteries SAFETY Precautions for Sanyo Ni-MH Battery Pack Then check the matters below Maintenance and CleaningIndicators Page Maintenance and Cleaning Cleaning the Projection Window Cleaning the Projector CabinetService Parts No 337 Maintenance and Cleaning Lamp ReplacementReset the lamp counter Lamp Handling Precautions Maintenance and Cleaning Lamp Replacement CounterTroubleshooting AppendixAppendix Image is out of focusRemote Control does not work Appears on the screenComputer Input/Video Input Appendix Menu TreeSound Computer InputSetting Progressive Reset Store Quit Normal WideAppendix Indicators and Projector Condition Projector ConditionAppendix Compatible Computer Specifications ON-SCREEN ResolutionTechnical Specifications Accessories Optional PartsService Port Connector Terminal Mini DIN 8-PIN Appendix Configurations of TerminalsDimensions Terminal Analog RGB Mini D-sub 15 pinLamp Replacement Label Appendix PIN Code Number MemoKM3A
Related manuals
Manual 75 pages 32.24 Kb

PLC-XL50 specifications

The Sanyo PLC-XL50 is a well-respected model in the realm of projectors, known particularly for its unique features and superior performance tailored for both professional and personal use. It embodies a blend of advanced technologies that make it an appealing choice for a variety of applications, including business presentations and educational settings.

One of the standout characteristics of the PLC-XL50 is its impressive brightness output, which is rated at 3000 ANSI lumens. This high brightness level ensures that images remain clear and visible even in well-lit environments, making it an optimal choice for conference rooms and classrooms. The projector utilizes a 3LCD technology, which means it is capable of delivering vibrant colors and excellent image quality while maintaining a high level of brightness. This technology reduces the chances of color separation artifacts that can sometimes occur with single-chip DLP projectors.

Additionally, the PLC-XL50 boasts a native resolution of XGA (1024 x 768 pixels), providing crisp images for presentations and video playback. Coupled with a contrast ratio of 500:1, users can expect deeper blacks and brighter whites, enhancing the overall viewing experience. The projector supports a wide range of input options, including VGA, composite video, and S-video, thus ensuring compatibility with various devices from laptops to DVD players.

The unit is also designed with convenience in mind. It features a compact form factor, making it easy to transport between locations, and it is lightweight enough for portability. The adjustable zoom and focus capabilities allow for flexible setup arrangements, enabling users to project larger images from shorter distances. This versatility is further enhanced by its keystone correction feature, which helps to maintain a square image, eliminating distortion when projecting from an angle.

Another notable attribute is its energy-efficient design. The PLC-XL50 is equipped with a long-lasting lamp life, which significantly reduces the frequency of bulb replacements and lowers overall operating costs. Furthermore, it includes a quiet fan operation, making it suitable for environments where noise is a concern.

In summary, the Sanyo PLC-XL50 is a robust projector that effectively combines high brightness, excellent color accuracy, and flexible connectivity options. Its advanced features make it a reliable choice for anyone in need of a projector that performs consistently across various settings.