Sanyo PLC-XL50 owner manual Installation, Positioning the Projector, Adjustable Feet

Page 14

Installation

Positioning the Projector

For the projector positioning, see the figures below.

The projector should be set perpendicularly to the plane of the screen.

A

A

 

 

 

 

 

 

-0.131’ ( -4.0 cm)

60”

0.265’ ( 8.1 cm)

80”

B

(Inch Diagonal)

Note:

•This projector is not equipped with an optical zoom. To adjust the screen size, change the throw distance.

•The brightness in the room has a great influence on picture quality. It is recommended to limit the ambient lighting in order to get the best image.

•All measurements are approximate and may vary from the actual sizes. Make sure to check the position of images by projecting images on the screen before installing the projector and screen, since each projector shows slight variations.

•Make sure to project images on a flat screen.

•Even slight warpage or irregularities of the screen may have an effect on the quality of the projected images.

Screen Size

60”

70”

80”

(W x H) mm

 

 

 

1219 x 914

1422 x 1067

1626 x 1219

4:3 aspect ratio

 

 

 

 

A

-0.131’ (-4.0 cm)

0.068’ (2.1 cm)

0.265’ (8.1 cm)

 

 

 

 

B

1.010’ (30.8 cm)

1.106’ (33.7 cm)

1.198’ (36.5 cm)

 

 

 

 

Adjustable Feet

Projection angle can be adjusted up to 1.0 degree with the adjustable feet.

Rotate the adjustable feet to adjust the position and tilt.

Keystone distortion of the projected image can be corrected by menu operation (pp.24, 45).

Adjustable Feet

14

Image 14 Contents
Model PLC-XL50 Features and Design Large Screen in Limited SpaceTable of Contents Safety Precaution To the OwnerSafety Instructions Safety Instructions Air Circulation Moving the ProjectorSide a Side B Side C Side D Side ECompliance Federal Communications Commission NoticeFront Back Top controls and Indicators e Exhaust VentPart Names and Functions Bottom Part Names and Functions Rear Terminal Part Names and Functions Top Part Names and Functions Remote Control Part Names and Functions Remote Control Battery Installation Operating RangePositioning the Projector InstallationAdjustable Feet Stand Installation Mounting the Rear Leg and the StandRear Leg Installation Connecting to Computer Cables used for connectionInstallation Connecting to Video Equipment Video, S-Video Computer Component Audio Installation Connecting the AC Power Cord Projector side AC outlet sideTurning On the Projector What is PIN code?Basic Operation Enter a PIN codeBasic Operation Turning Off the Projector Top Control Basic Operation How to Operate the On-Screen MenuRemote Control Select button On-Screen Menu Menu button Point buttonsFor video source Basic Operation Menu BarFor computer source Focus Adjustment Basic Operation Zoom AdjustmentScreen Position Adjustment Remote ControlCOMPUTER/VIDEO button Basic Operation Sound AdjustmentRemote Control Operation Freeze buttonBasic Operation Input Menu Computer InputInput Source Selection Source Select MenuPC System Menu Computer Input Computer System SelectionAuto ModeTo store the adjusted parameters Computer Input Auto PC AdjustmentDirect Operation Remote Control PC Adjust MenuComputer Input Manual PC Adjustment Computer Input Computer Input Image Level Selection BlackboardGreen Image Select MenuComputer Input Image Level Adjustment Screen Size Adjustment Digital zoom For zooming in and out the imagesDigital zoom + Auto Video Component Video InputInput Source Selection Video, S-Video, Component Video Input Input Source Selection RGB Scart 21-pin RGB ScartComponent Auto Video Input Video System SelectionVideo or S-Video Auto AV System Menu Video or S-VideoVideo Input Image Level Selection CinemaVideo Input Image1-4Tint Video Input Image Level AdjustmentColor Noise reduction ProgressiveVideo Input Screen Size Adjustment Language Setting Menu Language SettingSetting ZoomDisplay Uniformity adjBlue back Capture Logo Logo and Logo PIN code lock settingsLogo select Logo select CaptureLogo PIN code lock Enter a Logo PIN codeChange the Logo PIN code Terminal CeilingRear Input searchLamp control Power managementOn start To change the code for the projector Security Key lock, PIN code lock, Alarm settingsRemote control Key lock Key lockPIN code lock Enter a PIN codeChange the PIN code Change the PIN code lock settingChange the PIN code lock setting Change the PIN codeFan Factory defaultLamp Replacement icon Lamp counterSet and release the Antitheft alarm function Antitheft Alarm FunctionHow to Use the Antitheft Alarm Function IndicatorAntitheft Alarm Function Other settingsReplace the rechargeable batteries How to replace the rechargeable batteriesCharge the built-in batteries SAFETY Precautions for Sanyo Ni-MH Battery Pack Then check the matters below Maintenance and CleaningIndicators Page Maintenance and Cleaning Cleaning the Projection Window Cleaning the Projector CabinetService Parts No 337 Maintenance and Cleaning Lamp ReplacementReset the lamp counter Lamp Handling Precautions Maintenance and Cleaning Lamp Replacement CounterTroubleshooting AppendixAppendix Image is out of focusRemote Control does not work Appears on the screenComputer Input/Video Input Appendix Menu TreeSound Computer InputSetting Progressive Reset Store Quit Normal WideAppendix Indicators and Projector Condition Projector ConditionAppendix Compatible Computer Specifications ON-SCREEN ResolutionTechnical Specifications Accessories Optional PartsService Port Connector Terminal Mini DIN 8-PIN Appendix Configurations of TerminalsDimensions Terminal Analog RGB Mini D-sub 15 pinLamp Replacement Label Appendix PIN Code Number MemoKM3A
Related manuals
Manual 75 pages 32.24 Kb