Sanyo PLC-XW250K, PLC-XW200K owner manual Appendix, Troubleshooting

Page 63

Appendix

Troubleshooting

Before calling your dealer or service center for assistance, check the items below once again.

–Make sure you have properly connected the projector to peripheral equipment as described on pages 14-16.

–Make sure all equipment is connected to AC outlet and the power is turned on.

–When the projector does not project an image from the connected computer, restart the computer.

 

Problem:

– Solutions

 

 

 

 

 

 

No power

– Plug the power cord of the projector into the AC outlet.

 

 

 

– See if the POWER indicator lights red.

 

 

 

– Wait until the POWER indicator stops blinking to turn on the projector

 

 

 

again. The projector can be turned on after the POWER indicator

 

 

 

turns red. See page 18.

 

 

 

– Check the WARNING indicator. If the WARNING indicator lights red,

 

 

 

projector cannot be turned on. See page 58.

 

 

 

– Check the projection lamp. See page 61.

 

 

 

– Unlock the Key lock function for the projector. See page 53.

 

 

 

 

The initial display is not shown..

– Make sure Off or Countdown off are not chosen at display

 

 

 

function. See page 45.

 

 

 

 

The initial display is not same

– Make sure User or Off are not chosen at Logo (select)

 

as the default set..

function. See page 46.

 

Input signal switches automatically.. – Make sure Input search function is adjusted properly. See page 44.

(or does not switch automatically)

When the projector is on and you

– That is the Filter warning icon. See page 56.

 

press the input source buttons,

 

 

an icon other than the Lamp mode

 

 

icon appears.

 

 

 

 

 

An icon other than Input mode or

– That is the Lamp replacement icon or the Filter warning icon. See

 

Lamp mode icon appears..

pages 56 or 61.

 

 

 

 

Image is out of focus..

– Adjust focus of the projector. See page 23.

 

 

 

– Provide proper distance between the projector and the projection

 

 

 

screen. See page 12.

 

 

 

– Check the projection lens to see if it needs cleaning. See page 60.

 

 

 

– Moving the projector from a cool to warm place may result in

 

 

 

moisture condensation on the projection lens. In such cases, leave

 

 

 

the projector off and wait until condensation evaporates.

 

 

 

 

 

Image is Left/Right reversed..

– Check the Ceiling/Rear function. See page 49.

 

Image is Top/Bottom reversed..

– Check the Ceiling function. See page 49.

 

 

 

 

Picture is not bright enough.

– Check if the Contrast or Brightness is adjusted properly. See

 

 

 

pages 33, 40.

 

 

 

– Check if Image mode is selected properly. See pages 32, 39.

 

 

 

– Check the lamp control function. See pages 25, 52.

 

 

 

– Check the LAMP REPLACE indicator. If it lights, the end of lamp life

 

 

 

is approaching. Replace the lamp with a new one promptly. See page

 

 

 

61.

 

63

Image 63
Contents Network Supported Model PLC-XW200 PLC-XW250 PLC-XW200K PLC-XW250KFeatures and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Safety Instructions Air Circulation Installing the Projector in Proper PositionMoving the Projector Compliance AC Power Cord RequirementAC Power Cord for the United States and Canada AC Power Cord for the United KingdomPart Names and Functions Front BackBottom ⑥ LAN Connection Terminal Part Names and Functions⑦ Lamp Replace indicator ② Point Volume +/- buttons③ Auto Setup button ⑤ Power indicator② Auto SET button Part Names and Functions Remote ControlRemote Control Code Remote Control Operating RangeInstallation Adjustable FootPositioning the Projector Cables used for connection Installation Connecting to a ComputerInstallation Connecting to Video Equipment Audio OUT Computer in 1/ S-VIDEO in / Component For Continental Europe For the U..K Installation Connecting the AC Power CordNote Projector side AC outlet sideSelected Input Source and Lamp Control Input signal guidance windowBasic Operation Turning On the ProjectorPIN Code Input Dialog Box What is PIN code?Basic Operation Enter a PIN codeBasic Operation Turning Off the Projector Basic Operation How to Operate the On-Screen Menu Remote ControlTop Control For detailed functions of each menu, see Menu Tree on pages Basic Operation Menu BarNotes Basic Operation Zoom and Focus AdjustmentAuto Setup Function Keystone CorrectionBasic Operation Sound Adjustment Direct OperationMenu Operation Basic Operation Remote Control Operation Screen button Timer buttonNo Show button Image buttonComputer Input Input Source Selection RGB Computer 1/ComputerInput Menu Computer Input Computer System Selection Selecting Computer System ManuallyPC System Menu Auto PC adj Computer Input Auto PC AdjustmentPC adjust Menu To store adjustment parametersComputer Input Manual PC Adjustment Store ResetMode free Computer InputImage select Menu Computer Input Image Mode SelectionImage Adjust Menu Computer Input Image AdjustmentScreen Menu Screen Size AdjustmentDigital zoom CustomPosition H/V For zooming in and out the images Digital zoom +Input Menu Video InputInput Source Selection Video, S-video VideoRGB Scart ComponentComponent AV System Menu Component Video Input Video System SelectionVideo or S-video AV System Menu Video or S-videoCinema Video Input Image Mode SelectionBlackboard or Colorboard Video Input Image AdjustmentColor TintNoise reduction Off Disabled Lower reduction Higher reduction ProgressiveVideo Input Store MenuVideo Input Screen Size Adjustment Language SettingSetting Setting Menu LanguageAuto Keystone Auto setupAuto setup Input searchUser Power off? p.20Keystone BackgroundThis function allows you to customize the screen logo with Logo Logo and Logo PIN code lock settingsLogo PIN code lock CaptureLogo PIN code lock CaptureChange the Logo PIN code lock setting Enter a Logo PIN codeLogo PIN code change Computer CeilingRear TerminalPower management Shut downOn start Closed Caption Standby modeLamp control Lamp life control Remote controlPIN code lock Key lock PIN code lockSecurity Key lock and PIN code lock Key lockChange the PIN code lock setting Change the PIN codeEnter a PIN code Change the PIN code Lamp counter Lamp counter resetFan Fan controlFilter counter Factory defaultFactory default Filter counterInput Source Information Display InformationMaintenance and Cleaning Projector is shut down and the Warning indicator lights redNote Then check the matters below Resetting the Filter Counter Maintenance and Cleaning Cleaning the FiltersMaintenance and Cleaning Attaching the Lens Cap Cleaning the Projection LensCleaning the Projector Cabinet Reset the lamp replacement counter Maintenance and Cleaning Lamp ReplacementModel No.. of your projector PLC-XW200, PLC-XW250 Maintenance and CleaningReplacement Lamp Type No POA-LMP132 Service Parts No 345Appendix TroubleshootingAppendix PIN code dialog box appears Remote Control doesIndicator blinks or lights Image is distorted or runs offAppendix Computer Input Appendix Menu TreeComputer Input/Video Input SoundVideo Input SettingIndicators Appendix Indicators and Projector ConditionON-SCREEN Resolution Appendix Compatible Computer SpecificationsTechnical Specifications Optional Parts Appendix PJ Link Notice Appendix Configurations of Terminals Appendix PIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Dimensions KR5AC