Sanyo PLC-XW200K, PLC-XW250K owner manual Lamp control, Lamp life control Remote control

Page 52

Setting

Lamp control

Lamp control

This function allows you to change brightness of the screen.

High	Brighter than the Normal mode.
Normal	Normal brightness
Eco	Lower brightness reduces the lamp
	power consumption and extends the
	lamp life.

Lamp life control

Select the lamp operation when the total lighting time of a lamp exceeds the recommended total hours of use.

Mode 1	The lamp can be turned on even after
	exceeding the recommended total
Mode 2	hours of use.
Mode 2	The lamp can be turned on even after
	exceeding the recommended total
	hours of use. But the projector turns off
Note:	automatically after 3 minutes.
Note:

•Lamp mode cannot be changed for a while after turning on the projector. Lamp needs some time to stabilize after the power is turned on. Stored lamp mode will be active after the lamp is stabilized.

•If Mode 2 has been selected and the projection lamp exceedes the recommended total hours of use, the replacement icon will be displayed at the time of power- on. Then the projector will turn off after 3 minutes.

Lamp replacement icon

•The Lamp replacement icon will not appear when the Display function is set to Off (p.45), during Freeze (p.25), or No show (p.26).

Remote control

This projector provides two different remote control codes: the factory-set initial code (Code 1) and the secondary code (Code 2). This switching function prevents remote control interference when operating several projectors or video equipment at the same time.

When operating the projector in Code 2, both the projector and the remote control must be switched to Code 2.

To change the code for the projector:

Select either Code 1 or Code 2 in this Setting Menu.

To change the code for the remote control:

Press and hold both the MENU and IMAGE buttons together for 5 seconds or more. After changing the code, make sure the remote control operates properly.

Note:

Lamp life control

Remote control

•When different codes are set on the projector and on the remote control, any operation cannot be made. In that case, switch the code on the remote control to fit the code on the projector.

•If the batteries are removed from the remote control for a long period of time, the remote control code will be reset.

52

Image 52

Contents Model PLC-XW200 PLC-XW250 PLC-XW200K PLC-XW250K Network SupportedFeatures and Design Table of Contents Safety Precaution To the OwnerSafety Instructions Installing the Projector in Proper Position Safety Instructions Air CirculationMoving the Projector AC Power Cord Requirement AC Power Cord for the United States and CanadaAC Power Cord for the United Kingdom ComplianceFront Back Part Names and FunctionsBottom Part Names and Functions ⑥ LAN Connection Terminal② Point Volume +/- buttons ③ Auto Setup button⑤ Power indicator ⑦ Lamp Replace indicatorPart Names and Functions Remote Control ② Auto SET buttonRemote Control Operating Range Remote Control CodeAdjustable Foot InstallationPositioning the Projector Installation Connecting to a Computer Cables used for connectionInstallation Connecting to Video Equipment Audio OUT Computer in 1/ S-VIDEO in / Component Installation Connecting the AC Power Cord NoteProjector side AC outlet side For Continental Europe For the U..KInput signal guidance window Basic OperationTurning On the Projector Selected Input Source and Lamp ControlWhat is PIN code? Basic OperationEnter a PIN code PIN Code Input Dialog BoxBasic Operation Turning Off the Projector Remote Control Basic Operation How to Operate the On-Screen MenuTop Control Basic Operation Menu Bar For detailed functions of each menu, see Menu Tree on pagesBasic Operation Zoom and Focus Adjustment Auto Setup FunctionKeystone Correction NotesDirect Operation Basic Operation Sound AdjustmentMenu Operation Basic Operation Remote Control Operation Timer button No Show buttonImage button Screen buttonInput Source Selection RGB Computer 1/Computer Computer InputInput Menu Selecting Computer System Manually Computer Input Computer System SelectionPC System Menu Computer Input Auto PC Adjustment PC adjust MenuTo store adjustment parameters Auto PC adjComputer Input Manual PC Adjustment Reset Mode freeComputer Input StoreComputer Input Image Mode Selection Image select MenuComputer Input Image Adjustment Image Adjust MenuScreen Size Adjustment Screen MenuCustom Position H/VFor zooming in and out the images Digital zoom + Digital zoomVideo Input Input Source Selection Video, S-videoVideo Input MenuComponent RGB ScartVideo Input Video System Selection Video or S-videoAV System Menu Video or S-video Component AV System Menu ComponentVideo Input Image Mode Selection CinemaVideo Input Image Adjustment ColorTint Blackboard or ColorboardOff Disabled Lower reduction Higher reduction Progressive Video InputStore Menu Noise reductionVideo Input Screen Size Adjustment Setting SettingSetting Menu Language LanguageAuto setup Auto setupInput search Auto KeystonePower off? p.20 KeystoneBackground UserLogo Logo and Logo PIN code lock settings This function allows you to customize the screen logo withCapture Logo PIN code lockCapture Logo PIN code lockEnter a Logo PIN code Change the Logo PIN code lock settingLogo PIN code change Ceiling RearTerminal ComputerShut down Power managementOn start Standby mode Closed CaptionLamp life control Remote control Lamp controlKey lock PIN code lock Security Key lock and PIN code lockKey lock PIN code lockChange the PIN code Change the PIN code lock settingEnter a PIN code Change the PIN code Lamp counter reset FanFan control Lamp counterFactory default Factory defaultFilter counter Filter counterInformation Input Source Information DisplayProjector is shut down and the Warning indicator lights red Maintenance and CleaningNote Then check the matters below Maintenance and Cleaning Cleaning the Filters Resetting the Filter CounterCleaning the Projection Lens Maintenance and Cleaning Attaching the Lens CapCleaning the Projector Cabinet Maintenance and Cleaning Lamp Replacement Reset the lamp replacement counterMaintenance and Cleaning Replacement Lamp Type No POA-LMP132Service Parts No 345 Model No.. of your projector PLC-XW200, PLC-XW250Troubleshooting AppendixAppendix Remote Control does Indicator blinks or lightsImage is distorted or runs off PIN code dialog box appearsAppendix Appendix Menu Tree Computer Input/Video InputSound Computer InputSetting Video InputAppendix Indicators and Projector Condition IndicatorsAppendix Compatible Computer Specifications ON-SCREEN ResolutionTechnical Specifications Optional Parts Appendix PJ Link Notice Appendix Configurations of Terminals PIN Code Lock No Appendix PIN Code Number MemoLogo PIN Code Lock No Dimensions KR5AC