Hitachi cp-s318 user manual SCREEN Menu

Page 35
SCREEN Menu

CP-S317/327W/Vol2-E責了03.5.27 2:31 PM ページ 5

SCREEN Menu

With the SCREEN menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table.

MENU

MAIN

BLANK

MyScreen

PICTURE-1

START UP

ORIGNAL

PICTURE-2

MyScreen

 

 

 

 

INPUT

MyScreen Size

 

 

 

 

SCREEN

MyScreen Lock

 

 

OPTION

 

 

 

 

 

 

 

: SELECT

 

 

 

SCREEN Menu

 

 

 

 

 

 

 

 

Example : SCREEN Menu

 

 

 

 

 

 

 

 

 

(BLANK)

Item

 

 

 

 

Description

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Selection of BLANK Screen:

 

 

 

 

 

 

 

 

 

 

 

MyScreen

ORIGINAL

.

 

.

. .

.

 

.

 

 

 

 

 

 

 

The BLANK Screen may be voluntarily selected. The BLANK Screen is displayed when the screen

 

has been erased (i.e., made to vanish) by manipulating the BLANK button (please refer to the

 

“Temporarily Blanking the Screen” section of the separate booklet, Vol. 1 (Basic)).

BLANK

MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen

 

(or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen.

 

ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s).

 

Option screens: Various colored non-patterned (plain) screens displayed within the Menus.

The MyScreen and the ORIGINAL Screen will each change to a non-patterned (plain) black color screen several minutes after being displayed.

 

Selection of START UP Screen:

 

 

 

MyScreen

ORIGINAL

TURN OFF

 

The START UP Screen may be voluntarily selected. The START UP Screen is displayed when

 

no signal has been inputted, or when spec signals are being inputted.

 

MyScreen: Using the MyScreen category (see this Table, below), one can register a

START UP

desired screen (or screens). At the time of factory shipment, this is set as a non-patterned

 

(plain) blue color screen.

 

 

 

ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s).

 

TURN OFF: A non-patterned (plain) blue color screen.

The MyScreen and the ORIGINAL Screen will each change to the BLANK Screen several minutes after being displayed.

Registration of MyScreen:

When this item is executed, the MyScreen Menu for registration of MyScreen for the BLANK Screen and the START UP Screen is displayed. When operations are performed in accordance with this Menu, one can “cut” and register desired screens from among the received images within the display.

1.After the “Do you start capturing this picture?” message has been displayed, pressing the ESC (or RESET) button interrupts execution of the MyScreen. When the ENTER button is pressed, the picture becomes static (no longer moves), and a frame for picture cutting, as well as the message that follows below, appear. Please press the button when the screen you want to register is

MyScreen

currently being displayed.

2.When the “Move the capture area as you want.” message has been displayed, pressing the ESC (or RESET) button will eliminate the static state of the picture, and operations can be performed again from operation 1.

The frame can be moved using the Manual background , Manual background , Manual background , Manual background buttons. After designating the screen you want to register, pressing the ENTER button will initiate screen registration. The registration process takes approximately 1 minute to complete.

3.When the registration has been completed, the screen of the registered MyScreen, plus the message, “MyScreen registration is finished,” will be displayed for several seconds, after which the operation is terminated.

MyScreen Size

Selection of MyScreen display size:

x1

FULL

 

MyScreen Lock

Invalidation of MyScreen registration function:

TURN ON Manual backgroundManual background TURN OFF

When TURN ON is selected, the MyScreen category (see this Table, above) cannot be executed; in this way, one can prohibit rewrites (“writeovers”) of the MyScreen.

5

Image 35
Contents ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS NORSK PORTGÊS CP-S318W/CP-X328WMANUALE DISTRUZIONI Vol.1 Informazioni di base BRUKERHÅNDBOK Vol.1 GrunnleggendeUSING THE REMOTE CONTENTSSETTING UP CONNECTINGPartial Magnification Function PROJECTOR FEATURESUltra High Brightness Keystone Distortion CorrectionInsert the batteries into the remote 3 Connect the power cordConnect your devices to the projector 8 ~THE PROJECTOR PART NAMESTHE REMOTE CONTROL Raise or lower the projector to the SETTING UP THE PROJECTORAdjusting the Projectors Elevator Feet Press and hold in the elevator 1 buttonsIf 169 aspect ratio Adjusting the Screen Size and Projection DistanceIf 43 aspect ratio Indicates the corresponding reference page CONNECTING YOUR DEVICESNOTE About Plug-and-Play Capability Ports and CablesDesktop computer CONNECTING YOUR DEVICES continuedConnecting to a Computer Laptop computerIf using a component Connecting to a DVD PlayerConnecting to a VCR DVD playerRGB OUT RGB IN Connecting to a Display MonitorDisplay monitor 3 Closecover the battery USING THE REMOTE CONTROLPutting batteries into the remote control unit Operating the remote controlTurn on the projectors power TURNING ON THE POWERPrecautions Make sure that the power cord is firmly andUse the zoom ring to adjust the Selecting an Input SignalUsing the remote control If selecting RGB input Press the RGB button Using the projectors control panel Press the INPUT buttonCheck that the POWER indicator stops TURNING OFF THE POWERpanel or remote control control panel or remote controlthe volume ADJUSTING THE VOLUMEPress the VOLUME button buttons to adjustthe position ADJUSTING THE POSITION1 Press the POSITION button Use thePress the AUTO button USING THE AUTOMATIC ADJUSTMENT FEATUREAutomatic Adjustment for RGB Input Automatic Adjustment for Video Inputdirection of distortion to correct CORRECTING KEYSTONE DISTORTIONSPress the KEYSTONE button buttons to select thepress the POSITION button again to confirm your USING THE MAGNIFY FEATUREFREEZING THE SCREEN Press the MAGNIFY ON button1 Press the SEARCH button SIGNAL SEARCHINGSELECTING THE ASPECT RATIO TEMPORARILY BLANKING THE SCREENbuttons to adjust the level USING THE MENU FUNCTIONS2 Select a menu using the Select an item using theUSB Mouse/Keyboard Control You can use the remote control as a simplified mouse or keyboardOPERATING THE PC SCREEN PS/2, ADB, Serial Mouse ControlTHE LAMP Replacing the lamp THE LAMP continuedTurn on the projector, and use the menu to reset the filter Turn off the projector, and unplug the power cordApply a vacuum cleaner to to clean the air filterTHE AIR FILTER continued Turn off the projector, and unplug the power cord. Prepare aTurn on the projector power, and using the menu, reset the filter timerCaring for the lens Caring for the cabinet and remote control transmitterOTHER CARE Caring for the inside of the projectorCP-S317/327W/Vol2-E責了 03.5.27 230 PM ページ MAIN Menu MULTIFUNCTIONAL SETTINGSMAIN Menu PICTURE2 Menu PICTURE 1 MenuPICTURE 2 Menu PICTURE1 MenuINPUT Menu MULTIFUNCTIONAL SETTINGS continuedINPUT Menu SCREEN Menu SCREEN MenuOPTION Menu OPTION MenuWHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED Related MessagesFlashing of the orange lamp Regarding the Indicator LampsFlashing of the green lamp The green lamp is lightedPhenomena That May Easily Be Mistaken for Machine Defects WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED continuedSpecification SPECIFICATIONSDimension Diagram WARRANTY AND AFTER-SERVICE CP-S318/328W/TECHNICAl責了 03.5.27 239 PM ページ SIGNAL CONNECTOR PIN ASSIGNMENTTECHNICAL fH kHz EXAMPLE OF COMPUTER SIGNALResolution Signal modeThe following signals are used for the initial settings INITIAL SET SIGNALSPS/2 Mouse CONNECTION TO THE MOUSE CONTROLADB Mouse USB MouseRS-232C COMMUNICATION Communications setting3 Command data Command data chartIncreasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset CommandCommand data chart Command data chart continued KeystoneH DefaultH.Phase ContrastCP-S318/328W/TECHNICAl責了 03.5.27 239 PM ページ Pour les utilisateurs au Canada REGULATORY NOTICESFCC Statement Warning For the Customers in CANADAQR57451